Part B In the machine design the bed with a mass of 250 kg is moved by a lead screw which has a square thread profile. The lead screw is 20 mm in diameter with a thread pitch of 4mm and is made from steel. The coefficient of friction between the lead screw and the bed saddle is 0.15. Calculate the operating efficiency of the lead screw.

Part B In the machine design the bed with a mass of 250 kg is moved by a lead screw which has a square thread profile. The lead screw is 20 mm in diameter with a thread pitch of 4mm and is made from steel. The coefficient of friction between the lead screw and the bed saddle is 0.15. Calculate the operating efficiency of the lead screw.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
A square threaded power screw has an efficiency of 65% when raising the load. The coefficientof friction for the threads is 0.15, with the collar friction negligible. Determine the lead angle of thescrew.
An acme thread power screw that has a mean diameter of 25 mm and pitch of 5 mm is used to lift a load of 500 kg. If friction on threads is 0.1, determine the torque needed to turn the screw.
A double square thread power screw has a pitch of 6 mm and mean radius of 34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required to turn the screw.
The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2150 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque required to drive the screw and the efficiency of the screw.
A single square thread power screw has a lead of 7 mm and mean diameter of 35 mm. If it Is used to lift a load of 30 kN and coefficient of friction of thread is 0.18, find the torque required to turn the screw.
A double-threaded power screw is used to raise a load of 5 kN.The nominal diameter is 60 mm and the pitch is 9 mm. The threadsare Acme type and the coefficient of friction at the screw threads is0.15. Neglecting collar friction, calculate:(i) the torque required to raise the load;(ii) the torque required to lower the load; and(iii) the efficiency of the screw for lifting load.
The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to lift a load of 15 kN. The collar of the screw has an outside diameter of 100 mm and an inner diameter 60 mm Find the force applied at a radius of 950 mm if the coeffcient of friction for both threads and collar is 0.20.
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
A vertical power screw with double start square threads of 50 mm mean diameter and 11mm pitch is raised against a load of 10 kN by means of a hand wheel, the boss of which is threaded to act as a nut. A thrust collar, taking up the axial load,supports the wheel boss and has a mean diameter of 60mm. The coefficient of friction is 0.18for the screw and 0.16for the collar. If the tangential force applied by each hand to the wheel is 200 N, find suitable diameter of the hand wheel.
Determine the force required to raise a load of 3100 lbs., when a 2.5 in. triple threaded square power screw is used along with a collar having an outer diameter 4.5 in. and inner diameter 3.0 in. The pitch of the thread is 0.5 in. The operating force is applied at a radius of 38 in. Assume the coefficient of friction for both collar and threads as 0.2.
High-strength bolts are used in the construction of many steel structures. For a 1-in.-nominal-diameter bolt, the required minimum bolt tension is 51 kips. Assuming the coefficient of friction to be 0.30, determine the required couple that should be applied to the bolt and nut. The mean diameter of the thread is 0.94 in., and the lead is 0.125 in. Neglect friction between the nut and washer, and assume the bolt to be square-threaded.