Part (C)- Select the proper answer of the followings: 1. The direction of linear velocity of any point on a link with respect to another point on the same link is: (a) parallel to the link joining the points (c) at 45° to the link joining the points (b) perpendicular to the link joining the points (d) none of these 2. The magnitude of linear velocity of a point B on a link AB relative to point A is: (b) w (AB)? (a) w.AB where w = Angular velocity of the link AB. (c) w?. AB (d) (w: AB)? 3. The component of the acceleration, parallel to the velocity of the particle, at the given instant is called: (a) radial component (c) Coriolis component (b) tangential component (d) none of these

Part (C)- Select the proper answer of the followings: 1. The direction of linear velocity of any point on a link with respect to another point on the same link is: (a) parallel to the link joining the points (c) at 45° to the link joining the points (b) perpendicular to the link joining the points (d) none of these 2. The magnitude of linear velocity of a point B on a link AB relative to point A is: (b) w (AB)? (a) w.AB where w = Angular velocity of the link AB. (c) w?. AB (d) (w: AB)? 3. The component of the acceleration, parallel to the velocity of the particle, at the given instant is called: (a) radial component (c) Coriolis component (b) tangential component (d) none of these

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shaft of a turbine rotor, initially at rest, accelerates uniformly for 0.9s at 25 rad/s2. Compute and identify the nearest value of the angle turned through by the shaft in degrees during this time. a. 960o b. 580o c. 645o d. 720o Clear my choice
Find the Following: 1.Keq 2. Ceq 3. Natural angular velocity
Question 23 Repeat Q22, using instantaneous center of zero velocity method.
Explain Impulse and Momentum in details
A crank of length 30 cm, starting from an initial horizontal position P, rotates in a positive sense (counterclockwise) at a uniform rate of one revolution per second.a) Determine a function that gives the height of the end of the crank from the initial position line at any time t.
Derive the equations for displacement, velocity and acceleration of the mass in both the x&y directions
Angular Impulse and Momentum Principles To apply the principle of angular impulse and momentum to describe a particle's motion. The moment of a force about a point O, fixed in an inertial coordinate system, MO, and the angular momentum about the same point, HO, are related as follows: ∑MO=H˙O where H˙O is the time derivative of the angular momentum, HO=r×mv. Integrating this equation with respect to time yields the following equation: ∑∫t2t1MO dt=(HO)2−(HO)1 This equation is the principle of angular impulse and momentum, and it is often rearranged to its more familiar form (HO)1+∑∫t2t1MO dt=(HO)2 A centrifugal governor consists of a central rotating shaft that has two thin, pin-connected rods attached to it; a heavy sphere caps the end of each rod. (Figure 1) A centrifugal governor mechanically limits an engine's speed. A part of the engine turns the centrifugal governor, and if the speed exceeds a set amount, the height of the spheres decreases the driving force of the engine by…
Angular Impulse and Momentum Principles To apply the principle of angular impulse and momentum to describe a particle's motion. The moment of a force about a point O, fixed in an inertial coordinate system, MO, and the angular momentum about the same point, HO, are related as follows: ∑MO=H˙O where H˙O is the time derivative of the angular momentum, HO=r×mv. Integrating this equation with respect to time yields the following equation: ∑∫t2t1MO dt=(HO)2−(HO)1 This equation is the principle of angular impulse and momentum, and it is often rearranged to its more familiar form (HO)1+∑∫t2t1MO dt=(HO)2 A centrifugal governor consists of a central rotating shaft that has two thin, pin-connected rods attached to it; a heavy sphere caps the end of each rod. (Figure 1) A centrifugal governor mechanically limits an engine's speed. A part of the engine turns the centrifugal governor, and if the speed exceeds a set amount, the height of the spheres decreases the driving force of the engine by…
Consider an inward flow reaction turbine in which velocity of flow at inlet is 3.8m/s. The 1m diameter wheel rotates at 240rpm and absolute velocity makes an angle of 16° with wheel tangent. Determine (1) velocity of whirl at inlet, (2) absolute velocity of water at inlet, (3) vane angle at inlet, and (4) relative velocity of water at entrance. Show the schematic diagram and complete solution with units.
Differential Equations - Acceleration and velocity models
Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
The 100 mm diameter pulley on a generator is being turned by a belt moving 20 m/s and accelerating 6m/s^2. A fan with an outside diameter of 150 mm is attached to the pulley shaft. What are the linear velocity and acceleration of the tip of the fan?