Part II: For R1=100 Q, R2=200 SN and R3= 500 Q, calculate the equivalent resistance theoretically and experimentally in the following cases: 1) The three resistances are in series Regth=. . V= 20 v and I= 24 mA Regexp=. Compare the results: 2) The three resistances are in parallel Regth=.. V= 20 v and l= 0.338 A Regexp=...

Part II: For R1=100 Q, R2=200 SN and R3= 500 Q, calculate the equivalent resistance theoretically and experimentally in the following cases: 1) The three resistances are in series Regth=. . V= 20 v and I= 24 mA Regexp=. Compare the results: 2) The three resistances are in parallel Regth=.. V= 20 v and l= 0.338 A Regexp=...

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter27: Current And Resistance

Section: Chapter Questions

Problem 27.5CQ: How does the resistance for copper and for silicon change with temperature? Why are the behaviors of...

See similar textbooks

Similar questions

For the circuit shown in Fig.1 below, C1 = 5μF, C2 = 4μF, C3 = 6μF and ∆V = 65V. Find:(a) the equivalent capacitance, (b) the charge on each capacitor and (c) the potential differenceacross each capacitor.Figure 1: Problem 2.Problem 3For the circuit shown in Fig.2 below, determine the resistance R such that the current in R is0.50 A, with the sense from a to b.Figure 2: Problem 2.Problem 4A straight wire of length 0.40 m, carrying current I = 7.0 A is oriented at angle θ = 27◦ toa uniform magnetic field B = 1.2 T. The field is in the positive x-direction. Determine themagnitude and direction of the magnetic force on the wire.1
1. In a given fluid, positive ions, each with three excess protons, move towards right at a steady rate of 4.5 x 10^19 ions per minute and negative ions, each with two excess electron, move towards left at a steady rate of 2.5 x 10^20 ions per minute. Determine the current directed to the right. 2. Three resistors of 25 Ω, 30 Ω and an unknown resistance › are connected in parallel and the combination is connected to a 16 V source. If the total current delivered by the source is 1.5 A, determine the following:A. The value of R.B. The current in each resistor.C. Which resistor dissipates the highest power? Show your solution. Based on your answer, what conclusion can be made?
How does the resistance for copper and for silicon change with temperature? Why are the behaviors of these two materials different?
If two resistors with resistances R1 and R2 are connected in parallel, then the total resistance R, measured in ohms (Ω), is given by 1/R =1/R1 + 1/R2. If R1 and R2 are increasing at rates of 0.3 Ω/s and 0.2 Ω/s, respectively, how fast (in Ω/s) is R changing when R1 = 90 Ω and R2 = 120 Ω? (Round your answer to three decimal places.
What is the equivalent resistor, in units of Ohm, between the terminals a and b if you replace R1 by 4 Ohm, R2 by 1 Ohm and R3 by 5 Ohm resistor? Your result must contain two decimal places. Maximum of 5% of error is accepted in your answer.
1. 9. In the circuit shown in the figure above, a power supplier of 50 V is connectedacross a resistance network. If R1 = 20 Ω, R2 = 10 Ω, R3 = 10 Ω, and R4 = 40 Ω. Whatis the equivalent resistor of the circuit? 2. 10. What is the current flowing through the R4 resistor in the circuit shown in Problem 9? 3. 11. What is the voltage across the R1 resistor in the circuit shown in Problem 9? 3.
A 620-W heating coil designed to operate from 110 V is made of Nichrome wire 0.240 mm in diameter. (Assume ρ = 1.50 10-6 Ω · m, and α = 4.000 10-4(°C)−1 for Nichrome.) a) Assuming the resistivity of the Nichrome remains constant at its 20.0°C value, find the length of wire used. (b) Now consider the variation of resistivity with temperature. What power is delivered to the coil of part (a) when it is warmed to 1 200°C?
3. In Fig. 3, the resistances are R1 = 20.0 W and R2 = 40.0 W, and the ideal batteries have emfs E3=E1 = 10.0 V and E2 = 20.0 V. What is the potential difference Va - Vb? (Fig.3) ) (Show step by step solution)
Resistivity in metals increases with temperature according to the equation: ρ(T) = ρ0[1 + α(T - T0)] where α is the temperature coeficcient of restivity, and ρ0 is the restivity at the reference temperature T0. For a particular wire, the temperature coeficcient of restivity is α = 3.83 X 10-3 °C-1, and the restivity is ρ0 = 7.71 X 10-7 Ωm at the reference temperature T0 = 297°C. Find an expression for the temperature T2, at which the resistance of a particular wire will be twice as high as it is at the reference temperature T0. (Both temperatures are in degrees Celsius) Use this expression to find the temperature in degrees Celsius for T2. If the wire has a length of 1.00m and it has a circular cross section with a radius of 1.00cm, what is the resistance in ohms, at a temperature which is twice the reference temperature, T = 2T0 ?
3.A. How is the current of Resistor 1 (R1) effected as more resistors, Resistors R2 and R3, are added in series to it? Give answer and reasoning in 2-3 well written sentences B. How is equivalent resistance of a circuit affected as resistors are added in series? Can you identify a mathematical equation that describes the equivalent resistance of a circuit containing only resistors in series? Give your answer in 2-3 well written sentences as well as the equation for equivalent resistance for resistors in series.
Which of the following connections will give you the lowest resistance through the material: AB, CD, or EF? Calculate the resistance for each pair to confirm. Assume that the resistivity of the material shown is 0.025 Ωm.
How would you go about improving the determination of the electrical resistance of a given material in resistor color coding?