(Permeability). A cylindrical core sample of 1 cm length and 1 cm2 cross-section has upstream and downstream pressures of 2 atm and 1 atm, respectively, during steady state flow of water at 0.997 g/s at room temperature. Calculate the permeability of the core. Note: Water @ 25°C, viscosity = 1 cp, density of water = 0.997 g/cm3.

(Permeability). A cylindrical core sample of 1 cm length and 1 cm2 cross-section has upstream and downstream pressures of 2 atm and 1 atm, respectively, during steady state flow of water at 0.997 g/s at room temperature. Calculate the permeability of the core. Note: Water @ 25°C, viscosity = 1 cp, density of water = 0.997 g/cm3.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

Assuming a steady-state laminar flow, calculate the permeability from the following measurement made on core sample by using air. Flow rate = 2 cm3 /sec, T = 65°F, upstream pressure = 30 psi, downstream pressure = 14.7 psi, A = 0.004 ft2, L = 1.181 in, viscosity = 0.018 cp also calculate flow rate in bbl/day.
A cylindrical core sample of 1 cm length and 1 cm^2 cross-section has upstream and downstream pressures of 2 atm and 1 atm, respectively, during steady state flow of water at 1.005 g/s at room temperature. Calculate the permeability of the core. (Water @ 25 °C, viscosity = 1 cp, density of water = 0.997 g/cm^3.)
At 60°C the surface tension of mercury is 0.47 N/m. What capillary height changes (mm) will occur in this fluid when it is in contact with air in a glass tube of radius 0.25 mm? Use wetting angle = 130° and unit weight = 132,300 N/m3
A cylindrical core sample of 1.5 cm length and 1.2 cm2cross-section has upstream and downstreampressures of 2 atm and 1.25 atm, respectively, during steady state flow of water at 1.00 g/s at roomtemperature. Calculate the permeability of the core. (Water @ 25 °C, viscosity = 1 cp, density of water = 0.997 g/cm3).
You are being tasked as a wind tunnel engineer to investigate the performance of newly designed high-speed wind tunnel in UPNM. An exhaust gas flows through a nozzle where the inlet area is 5,000 cm2.At this inlet, the gas has a velocity of 1,200 m/s, temperature of 1,500oC,and pressure of 6,000 kPa. Initial measurement revealed that the pressure at the exit of the wind tunnel is 100 kPa. Based on this information, analyze and investigate ; i. Mach number at inlet of the nozzle ii. The velocity of gas at exit iii. The area of the nozzle at exit Take specific heat ratio for the exhaust gas, ? to be 1.7 and the gas constant, R to be 205 J/kg.
Air (diatomic, MW = 28.8664 g/mol) at 1.7 atm gage (where Pam = 1 atm) and 15°C enters a 70-m long horizontal 75-mm-ID steel pipe (€ = 4.6(10) m). The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the absolute pressure (atm) at the discharge end of the line? Use Churchill equation for the friction factor.
Air at 1.7 atm gauge and 15°C enters a horizontal 75-mm steel pipe that is 70 m long. The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the pressure at the discharge end of the line?
Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
A steam generator generates flue gas at an average temperature of 260 C inside a Chimney. The theoretical draft is 0.5 kPa and the ambient condition of the air is 21 C and 100 kPa. Assume the coefficient velocity to be 0.30 and the molecular weight of the flue gas is 32. For air-fuel ratio requirements per second of 15, calculate: a. The diameter of the Chimney, meter b. The theoretical draft, cm H₂O
Water at 27°C flows with a mean velocity of 1 m/s through a 1 km-long pipe of 0.25 m inside diameter. Answer the following: a. Is the flow hydrodynamically fully developed? Support your answer with calculations. b. Is the flow thermally fully developed? Support your answer with calculations. c. What is the pressure drop over the pipe length, if the pipe surface is smooth? (Ans: 0.289 Bar) d. What is the pump power requirement, if the pipe surface is smooth? (Ans: 1.42 kW)
Experimental measurements of the convection heat transfer coefficient for a square bar in cross flow yielded the following values: Assume that the functional form of the Nusselt number is Nu = C*Rem*Prn, where C, m, and n are constants. Also, assume that air temperature does not change in the following problem.A. What will be the convection heat transfer coefficient for a similar bar with L = 1 m when V = 15 m/s?B. What will be the convection heat transfer coefficient for a similar bar with L = 1 m when V = 30 m/s?
Calculate the power required per meter of width of stream to force lubricating oil through the gap between two horizontal flat plates under the following conditions: Distance between plates, 6 mm Flow rate of oil per meter of width, 100 m3h Viscosity of oil, 25 cP Density of oil, 0.88 g/cm3 Length of plates, 3 m Assume that the plates are very wide in comparison with the distance between them and that end effects can be neglected.