pie Loa A simply supported structure is composed of two members AC and BD (connected by a pin joint at B). Configurations of the structure, pin supports (i.e., at points C and D) and external loadings exerted on the structure are shown in the figure. 150 mm 400 mm 300 mm Given the allowable normal stress of rod BD is 200 MPa, Al and the diameter of rod BD is 20 mm, determine the maximum uniformly distributed load w that may be applied to the member AC.

pie Loa A simply supported structure is composed of two members AC and BD (connected by a pin joint at B). Configurations of the structure, pin supports (i.e., at points C and D) and external loadings exerted on the structure are shown in the figure. 150 mm 400 mm 300 mm Given the allowable normal stress of rod BD is 200 MPa, Al and the diameter of rod BD is 20 mm, determine the maximum uniformly distributed load w that may be applied to the member AC.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.11P: The figure shows an idealized structure consisting of an L-shaped rigid bar structure supported by...

See similar textbooks

Similar questions

Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
The figure shows an idealized structure consisting of an L-shaped rigid bar structure supported by linearly elastic springs at A and C. Rotational stiffness is denoted ßRand translational stiffness is denoted ß. Determine the critical load Pcrfor the structure.
An elliptical exerciser machine (see figure part a) is composed of front and back rails. A simplified plane-frame model of the back rail is shown in figure part b. Analyze the plane-frame model to find reaction forces at supports A, B. and C for the position and applied loads given in figure part b. Note that there are axial and moment releases, at the base of member 2 so that member 2 can lengthen and shorten as the roller support at B moves along the 30° incline. (These releases indicate that the internal axial force N and moment M must be zero at this location
A cable and pulley system at D is used to bring a 230-lcg pole (ACB) to a vertical position, as shown in the Figure part a. The cable has tensile force T and is attached at C. The length L of the pole is 6.0m, the outer diameter is d = 140 mm. and the wall thickness is t = 12 mm. The pole pivots about a pin at A in figure part b. The allowable shear stress in the pin is 60 MPa and the allowable bearing stress is 90 MPa. Find the minimum diameter of the pin at A in order to support the weight of the pole in the position shown in the figure part a.
An inflatable structure used by a traveling circus has the shape of a half-circular cylinder with closed ends (see figure). The fabric and plastic structure is inflated by a small blower and has a radius of 40 ft when fully inflated. A longitudinal scam runs the entire length of the "ridge" of the structure. If the longitudinal scam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0,5 psi and the structure is fully inflated?
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
Continuous cable A DB runs over a small friction less pulley al D to support beam OABC, which is part of an entrance canopy for a building (see figure}. The canopy segment has a weight W = 1700 lb that acts as a concentrated load in the middle of segment AB. (a) What is the maximum permissible value of load P at C if the allowable force in the cable is 4200 lb? (b) If P = 2300 lb, what is the required diameter of pins A, B, and D? Assume that the pins are in double shear and the allowable shear stress in the pins is 10 ksi.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.
A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
The figure shows an idealized structure consisting of a rigid bar with pinned connections and linearly elastic springs. Rotational stiffness is denoted R, and translational stiffness is denoted . Determine the critical load PCTfor the structure from the figure part a. Find PCIif another rotational spring is added at B from the figure part b.
An idealized column is composed of rigid bars ABC and CD joined by an elastic connection with rotational stiffness ßRat C. There is an elastic support at B with translational spring stiffness ß and a pin support at D. Find the critical buckling loads for each of the two buckling modes of the column in terms of ßL. Assume that ßR= ßL2. Sketch the buckled mode shapes.