roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB. Figure. rod In Problem 1, determine the required diameter of the pin at A if the allowable stress is 60 MPa (double shear). 2m. 2m. B

roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa. Neglect the weight of the bar AB. Figure. rod In Problem 1, determine the required diameter of the pin at A if the allowable stress is 60 MPa (double shear). 2m. 2m. B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Related questions

Q: A bar AB of length L and uniform cross section is attached to rigid supports at A and B before being…

A: Let the bar AB have a uniform cross-section of area = A Drawing the FBD of the bar AB:

Q: Q2) For the problem shown in the figure, - Find the axial displacement at the end B - Determine the…

A: for solution refer below images.

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Given data as per question compressive load of P = 55 kips α= 30°. calculating the inclined plane…

Q: Two holes have been formed through a steel bar and a centered axial load is applied as shown in the…

A: Given: P = 32 kN Diameter of hole A = 20 mm Diameter of hole B = 50 mm The steel bar is = 100 x 15…

Q: Two plates are connected by bolts as shown in the figure. Compute the maximum axial stress that each…

Q: Calculate the force which can be applied in the punch shown in the figure if the allowable shear…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

Q: A circular tube AB is fixed at one end and free at the other end. The tubeis subjected to axialforce…

A: In this question, we determine the maximum normal stress Maximum normal stress, σ=PA here, P is…

Q: Each of the four links in Figure has an 8x36mm uniform rectangular cross section and each of the…

A: Consider the free body diagram as shown below for the link ABC. From the moment equilibrium about…

Q: Figure. Calculate the maximum axial stress of the shaft if the average punching shear stress in the…

A: Given: The average punching shear stress =100 MPa The average bearing stress = 125 MPa The diameter…

Q: In figure shown, the allowable normal stress is 3.5 ksi, allowable shear stress is 1.2 ksi. Ift =…

A: (a) Draw the free-body diagram of joint A.

Q: A compression load of P= 50 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the…

Q: The member, shown in the figure, is under tensile load of P=15 kN. The member has uniform thickness…

Q: 100 kN lsize as sho 80 [A find the diameter of the rivet. 18. A bracket in the form of a plate is…

A: Given Load= 100 kN Maximum shear stress = 70 MPa Cursing stress = 100 MPa To find Diameter…

Q: 1:in the following arrangement of structur allowable shear stress in pin C is 16 Mpa calculate the…

A: Given;- W=36N/m D=10mm Shear stress=16Mpa

Q: A solid steel bar with a diameter of 50 mm is subjected to three forces as shown in the figure,…

A: In the given problem, the main stresses will be developed at point B due to 1200N force which will…

Q: 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If…

A: P= Stress x Arivets P=80[1/4 π (202)] P=8000 π N From bearing of plate material:P=σbAb 8000 π = 140…

Q: An external force P =1800 Ib is applied to the frame shown below via a cable that passes over a…

A: we first have to know the forces acting on the system by drawing FBD of cable pulley system and…

Q: The control arm in the figure is subject to the loads shown. Determine the required diameter of the…

A: allowable shear stress = 8 ksi.

Q: An iron column of annular cross-section has an outer diameter of 200 mm and is subjected to a force…

A: Given Data⇒Iron column of annular cross-sectionOuter diameterD=200 mm=0.2 mForceF=75 KN=75×103…

Q: A steel plate of dimensions 2.5 × 1.2 × 0.1 m is hoisted by a cable sling that has a clevis at each…

Q: For the figure shown determine the value of the maximum normal stresses, due to the change of…

A: Calculate the reaction at the left end support as follows, RL=10×250+5050+500+250+50RL=3.53 kN,…

Q: Q4(10 Marks): For the structure shown in the figure, calculate the size of the bolt and the area of…

A: σAT=Allowable Stresses in Tension=124 MPaσAB=Allowable Stresses in Bearing=3.44 MPa

Q: A load of 7,000 N acts on the machine part shown in Fig. 5a. The machine par thickness of 15 mm…

Q: The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are…

Q: 03. Find the maximum allowable value of P for the column shown below. The cross-sectional areas and…

Q: For the figure shown below. Calculate the increase in vertical stresses (Ac) at point A at depth of…

Q: 1. In the figure shown, determine the stress in the cable C if its area is 600 mm². Neglect the…

Q: A flat steel bar 6 in wide by 1.5 in thick has axial loads applied with 1.250-in diameter pins in…

A: Find stresses at required sections

Q: figure. Determine the required cross-sectional area of the bar BC if the allowable stresses are 100…

Q: The lap joint shown if Fig. is fastened by four 3/4 inch diameter rivets. Calculate the maximum safe…

Q: .The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with a…

A: Divide the entire section into the segment and calculate the stress induced in the section. Now draw…

Q: Find the smallest diameter for the one bolt that can be used in the figure if P = 90 kN. The working…

A: The given figure shows a single riveted joint with double plate To find : the area of the bolt…

Q: Q5(): For the truss shown in the Figure, if the diameter of pins at A and F are 2 in. and 1.5 in.,…

Q: Droblem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with diameter d=10…

Q: Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across…

A: Given: The dimension, n = 7/4 in The dimension, a = 15/32 in The dimension, e = 27/32 in The…

Q: The bracket shown in the figure below is fixed supported and has an applied force of 5kip with 40…

Q: A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: C 800 mm 18 mm dia. Rectangular bar B D 16 mm thick 25 mm 400 mm A F - F -800 mm

A: Given Data The force given is: 24 kN The height of the complee member is: 1200 mm The thickness of…

Q: Calculate the average stress in section a-a of the junction shown in the figure when applying force…

A: Let us assume that the diameter of the bolt is d in mm.

Q: a. Calculate the largest tensile and compressive stresses that occur in section a-a shown in the…

Q: Q) In Fig.(1), the shaft is subjected to a reversed load P = (2700 to - 900) N. Find the length (L),…

Q: 140mm 450 mm 100 mm | I kN In the figure, a force of 1 kN is applied by means of an arm connected to…

Q: The compound steel bar shown in Figure is made of three uniform segments marked as 1, 2 and 3 of…

A: net force acting on segment 1 : +80-40+25 kN = 65 kN

Q: The pinned members shown in figure carry the loads P and 2P. All bars have cross-sectional area A.…

Q: (3): A steel bar ABCD (4m) long is subjected to forees as shown in Figure. Find the stresses in each…

A: given:

Q: The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are…

Q: The figure below is a bracket which fastened by a bolts with a diameter of 0.5 inch. Compute the…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Solve the problems as stated below. Draw the figure and the FBD.
Problems
1. In the figure shown, determine the diameter
of the rod C if the allowable stress 86.60 MPa.
Neglect the weight of the bar AB.
Figure.
rod
2. In Problem 1, determine the required
diameter of the pin at A if the allowable
stress is 60 MPa (double shear).
A
2m.
2m.
В
60°
30 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
An element on the top surface of the fuel tanker in Problem 7.2-1 is in biaxial .is in the and is subjected to stresses a, = 6250 psi and a. = -1750 psi, as shown in the figure. Using Mohr s circle, determine the following: (a) The stresses acting on an element oriented at a counterclockwise angle ? = 550 from the x axis. (b) The maximum shear stresses and associated norm al stresses. Show all results on sketches of properly oriented elements.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A capped cast-iron pipe is compressed by a brass rod, as shown. The mil is turned until it is just snug, then add an additional quarter turn to pre-compress the cast-iron pipe. The pitch of the threads of the bolt ap = 52 mils (a mil is one-thousandth of an inch). Use the numerical properties provided. (a) What stresses a and arwill be produced in the cast-iron pipe and brass rod. respectively, by the additional quarter turn of the nut? (b) Find the bearing stress ahbeneath the washer and the shear stress t(in the steel cap.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.