pipe with an outside diameter of 2.7 inches. insulate with a 2 inches. layer of asbestos (ka = 0.396 btu-in./hr-ft-F), followed by a layer of cork 1.5 inches. thick (kc = 0.30 btu-in/hrft-F). if the temperature of the outer surface of the cork is 91 F, calculate the heat lost per 100 ft of insulate pipe. The temp of the inner surface of the pipe is 275 F.

pipe with an outside diameter of 2.7 inches. insulate with a 2 inches. layer of asbestos (ka = 0.396 btu-in./hr-ft-F), followed by a layer of cork 1.5 inches. thick (kc = 0.30 btu-in/hrft-F). if the temperature of the outer surface of the cork is 91 F, calculate the heat lost per 100 ft of insulate pipe. The temp of the inner surface of the pipe is 275 F.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.39P

See similar textbooks

Similar questions

A pipe with an outside diameter of 3.5 in. is insulated with a 3 in. layer of asbestos (ka=0.396 BTU-in/hr- ft2 - 0 F), followed by a layer of cork 1.5 in. thick (kc=0.30 BTU-in/hr-ft2 - 0 F). If the temperature of the outer surface of the cork and pipe is 1000 F and 3000 F, respectively, calculate the heat lost per 100ft or insulated pipe.
a pipe with an outside diameter of 2.5 inches is insulated with 2 inches layer of asbestos ( K= 0.396(btu-in)/(hr-ft-F) followed by a layer of cork 1.5 inches thick ( K= 0.30 (btu-in)/ft (hr-ft-F). if the temperature of the outer surface of the cork and pipe is 90 F and 290 F RESPECTIVELY, calculate the heat loss per 100 ft of insulated pipe in btu/hr
65. It is required to insulate a kitchen oven with cork board (k = 0.043 W/mK) so that the heat losses from the oven does not exceed 400 W/m² when the inner surface of the oven is at 225°C and the outer surface of the oven is at 40°C. The thickness of insulation required is nearly
A 1 in. o.d. (outer diameter) tube reactor is insulated with a 3 inch layer of asbestos. If the temperature of the outer surface of the insulation is 100 °F and the rate of heat loss per foot of reactor length is 50 BTU/hr, what must the temperature of the inside of the reactor be? [for asbestos, k = 0.105 BTU/hr ft °F]
A steel pipe of outside diameter of 0.051 m is insulated with a 0.0064-m thickness of asbestos followed by a 0.0254-m layer of fiber glass. If the pipe wall is 315.6o C and outside insulation is 37.8o C, what is the temperature between the asbestos and fiber glass? kasbestos = 0.166 W/mo C and kfiber glass = 0.0485 W/mo C.
The case-to-ambient thermal resistance of a power transistor that has a maximum power rating of 15 W is given to be 25°C/W. If the case temperature of the transistor is not to exceed 80°C, mark the power at which this transistor can be operated safely in an environment at 40°C.. a)Between 1.0 to 1.5 W b)Between 1.5 to 2.0 W c)Between 2.0 to 2.5 W
The average thermal conductivity of the walls (including windows) and roof of a house in the figure shown below is 4.8  10-4 kW/m · °C, and their average thickness is 20.8 cm. The house is heated with natural gas, with a heat of combustion (energy given off per cubic meter of gas burned) of 9,300 kcal/m3. How many cubic meters of gas must be burned each day to maintain an inside temperature of 25.9°C if the outside temperature is 0.0°C? Disregard surface air layers, radiation, and energy loss by heat through the ground. m3 A house has a rectangular base and a roof that peaks along a line above the center of the house and parallel to the length of the house. This roof slopes downward from the peak to each edge at an angle of 37.0° with the horizontal. The length of the front of the house is 10.0 meters. The width of the house is 8.00 meters. The height from the front of the house up to the edge of the roof is 5.00 meters.
The average thermal conductivity of the walls (including windows) and roof of a house in the figure shown below is 4.8  10-4 kW/m · °C, and their average thickness is 20.8 cm. The house is heated with natural gas, with a heat of combustion (energy given off per cubic meter of gas burned) of 9,300 kcal/m3. How many cubic meters of gas must be burned each day to maintain an inside temperature of 25.9°C if the outside temperature is 0.0°C? Disregard surface air layers, radiation, and energy loss by heat through the ground.
A 3 inch schedule 40 pipe is covered with two layers of                                                 insulations. The inner layer (k1 = 0.050) is 2 inches thick and                                                 the outer layer (k2 = 0.037) is 1(1/4) inches thick. Calculate                                                 the heat loss, in Btu/hr per unit length, if the outer surface                                                 temperature of the pipe is 670°F and the outer surface                                                 temperature of the outer layer of insulation is 100°F.
A typical temperature coefficient of monocrystalline solar panel (300 W) rated at 25o C is -0.5%/o C. The rooftop solar panel power delivery at 65o C is a. 200 W. b. 230 W. c. 210 W. d. 240 W. e. 220 W.
Answer this ASAP,thx Furnace walls are lined with 3 layers of firebrick with a thickness of 6 in (k=0.95 Btu/h.ft.°F), insulating brick (k-0.4 Btu/h.ft.°F) and common brick (k=0.8 Btu /h.ft.°F) Firebrick inlet temperature, T₁ = 1800°F, maximum insulating brick temperature, T₂ = 1720°F and T3 = 280°F. 1. Calculate the thickness of the insulating brick layer. 2. If the common brick is 9 in., calculate the exit temperature.
A cold-storage room is constructed of an inner layer of 11 mm of pine with thermal conductivity of 0.15 W/m K, and an outer layer of 75 mm of concrete with thermal conductivity of 0.75 W/m K. The wall surface temperature is 253 K inside the cold room and 299 K at the outside surface of the concrete. Calculate the heat loss in W per 1 m2. Please keep one decimal and take positive value for the final answer.