ple 10.11 The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa.  i)                    Determine the maximum shear stress in the shaft. ii)                  In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii)                Determine the resultant percentage weight reduction

Q: 4. Compute for the induced stress, in MPa, of a steel solid shafting of 6 cm diameter and 5 m in…

A:

Q: A single solid circular shaft 400 mm diameter running at 200 RPM, is to be replaced by two hollow…

A: Given Data: The diameter of the solid circular shaft is, d=400 mm. The speed of the solid circular…

Q: PROBLEM 1. A steel marine propeller shaft 11 inch...in diameter and 12 ft long is used to transmit…

A:

Q: made by wrapping wire 25mmØ around a forming cylinder 175mm in diameter. (a)Compute the number of…

A:

Q: A 5 ft long solid SAE4340 OQT1000 steel shaft is required to transmit a power of  180 HP. The shaft…

A:

Q: The timber beam loaded as shown has the cross section shown. If the working flexure stress is…

A: Given Data: The working flexure stress of the beam is, σb=16 MPa=16 MPa×N/mm2MPa=16 N/mm2. The…

Q: A solid steel shaft must not twist through more than 30 in a 6-m length when ted to a torque of 12…

A: Given Twist angle = 30 Length =  6m Torque = 12 kNm Modulus of rigidity = 83 GPa To find Smallest…

Q: PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters…

A:

Q: that varies uniformly from 1.92kpa at the top to 1.44kpa at the base. The pole is has an outside…

A:

Q: Do the stress concentrations exist on a shaft?

A: Stress concentration is increase in stress at particular point where stress is more because of hole…

Q: " A thick steel cylinder which has an inside diameter of 1m is subjected to an internal pressure of…

A:

Q: An automotive shaft manufacturing facility wants to reduce the material cost of the shaft. Propose a…

A: When we want the shaft to carry shear stress on the outermost edge, the most preferred one is hollow…

Q: Problem 16.7. A hollow shaft of external diameter 120 mm transmits 300 kW power at 200 r.p.m.…

A: As per the Bartleby policy, I can solve only the first question. Kindly repost the other questions…

Q: Problem 16.9. A solid eylindrical shaft is to transmit 300 kW power at 100 r.p.m. (a) If the shear…

A: a) Torque in the shaft can be determined as

Q: A shaft is made of an aluminum alloy having an allowable shear stress of Tallow = 118 MPa (Figure 1)…

A:

Q: What is the area of the tube? What is the total length of the median line? sheari

A:

Q: A helical spring is made by wrapping wire 25mmØ around a forming cylinder 175mm in diameter.…

A:

Q: A solid circular shaft is subjected to pure torsion. The ratio of maximum shear to maximum normal…

A: Since the solid circular shaft is subjected to pure tension therefore σx=0 and σy=0 Maximum…

Q: "4₂ A two celled tube with wall thickness 0.5 mm is subjected to a torque of 10 N.m as shown in…

A: Given data: t = 0.5 mm = 0.0005 m two cell tubes with square shape. their side (a) =50 mm = 0.05 m…

Q: 8.2 (A). Calculate the dimensions of a hollow steel shaft which is required to transmit 750 kW at a…

A:

Q: As part of an innovation policy introduced within the company to research into newer design of…

A: Given Diameter ratio d/D = 3/5 Power = 600kW = 600 × 103 W N= 110 rpm Max torque = 12% Mean torque…

Q: Question 4 A shaft used for a water pump has a diameter of 50 mm and a length of 0.7 m long and is…

A: GIVEN DATA- a) Diameter D=50mm , L=0.7m , G=90GPa , Torque T=1200Nm b) Hollow shaft with internal…

Q: experiment: Torsion test Discussion: 1. Does plane section (square plane) on the surface of the…

A:

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A:

Q: A thin metal pipe of mean radius R, thickness t and length L, has its ends closed and is full of…

A: given data,Mean radius=RThickness=tLength=L

Q: Please check attach file

A: Given Data The solid shaft diameter d=240mm The outer diameter of hollow shaft=d0=240mm Allowable…

Q: Question 19 A section of a rotating shaft is under an alternating bending moment of 70Nm and a…

A:

Q: 4. A hollow shaft with outside diameter of 98mm if it is subjected to a maximum torque of 5758N-m.…

A:

Q: A machine shaft is supported on bearings 1.2 m apart is to transmit 150 kW at 300 rpm while…

A: Given      Power, P = 150 kW     Speed, N = 300 rpm Shear stress = 50 MPa Find   Shaft diameter, d

Q: a 1.5 inch shaft has operating speed of 100 rpm and safety factor of 12. How much horsepower can it…

A: Given data:

Q: Q. 7: Two shafts of same material and same length are subjected to same torque. If the first shaft…

A: Given data: dh=34DH Need to compare the weight of two shafts.

Q: A line shaft rotating at 55 RPS is to transmit 28 kW. The shaft may be assumed to be made of mild…

A: The given values are - P=28×103W , N60=55 rps, ζ=85 MPa P=T.ϖ where…

Q: 1. A drive shaft to the blades of a helicopter transmits 800 kW at 200 rev/min. Neglecting…

A: Given, Power - 800kW N-200rpm L-2m or 2000mm C-26900MPa, Do=2Di

Q: 14. A steel shaft is subjected to completely reversed bending moment of 800 N-m and a cyclic…

A:

Q: A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft…

A: P=15000Hp N=300rpm

Q: A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the…

A: Given: τallow=300 MPaP=200kWN=300 rpmD=100 mmwkey=10 mm

Q: 8.20 At a certain point on the outside of a shaft, which is subjected to a torque, and a bending…

A:

Q: A shaft is made of an aluminum alloy having an allowable shear stress of Tallow=104 MPa. (Figure 1)…

A: Given Data: Allowable stress σallowable=104 MPa  Shaft diameter d=115mm=0.115 m Find: Determine the…

Q: The initial consideration is to use an electric motor to spin the central shaft. For this purpose a…

A:

Q: A solid rotating shaft of 5.08 cm in diameter and 0.914 m in length has a central load of 362.87 kg…

A:

Q: 5. A propeller solid shaft of a ship with 200 mm diameter transmit a power of 5 MW at 500 r.p.m. It…

A: The diameter of solid shaft, The power of solid shaft, The speed of solid shaft, Now, the power…

Q: Problem: Use the elasticity theory to determine the maximum shearing stress, the angle of twist per…

A: Elasticity theory is concerned with the connection between forces applied to an item and the…

Q: Question 2 A composite shaft is comprised of a solid inner rod (shaft 1) made of a steel with an…

A: Introduction: Stress analyses in composite driveshafts are critical because they can induce…

Q: A hollow shaft with an internal diameter equal to one-third of its external diameter is to replace a…

A: Given Data The internal diameter for the hollow shaft is di=13dodo=3di Here di is the internal…

Q: A composite shaft is comprised of an inner solid steel shaft 1/6 ft in diameter slipped over with a…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.