PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. a) What is the largest torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa? b) What torque should be applied to the end of the shaft to produce an angle of twist of 2 degrees? Modulus of rigidity of 60 mn 40 mm steel is 77 GPa. 1.5 m

PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. a) What is the largest torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa? b) What torque should be applied to the end of the shaft to produce an angle of twist of 2 degrees? Modulus of rigidity of 60 mn 40 mm steel is 77 GPa. 1.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the maximum permissible torque on a hollow shaft if the maximum allowable shearing stress is 83 MPa. D=75mm and d=60mm. A)4788 Nm B)4316 Nm C)4059 Nm D)4532 Nm
A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diam-eters respectively equal to 40 and 60 mm ). (a) What is the larg-est torque that can be applied to the shaft if the shearing stress is not to exceed 120 MPa? (b) What is the corresponding minimum value of the shearing stress in the shaft?
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at the ends. What is the diameter of a solid steel shaft that resists the same torques at the same maximum shear stress.
A hollow shaft of outer diameter 40 mm and inner diameter of 20 mm is to be replaced by a solid shaft to trandmit the same torque at the same maximum stress. What should be the diameter of the solid shaft?
A) Define the following terms; I)A propeller shaft for a small machine is made of a solid steel bar 104mm in diameter.The allowable stress in shear is 48MPa, and the allowable rate of twist is 2.0° in 3.5meters.Assuming that the shear modulus of elasticity is G=80GPa, calculate the maximum torque that can be applied to the shaft.
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
A hollow steel shaft 2304mm long is to be designed to transmit a torque of 28350 kJ. The shear modulus of elasticity, G = 82,740 GPa for steel. The total angle of twist of the length of the shaft is must not exceed 6 degrees. And the shear stress in the shaft must not exceed 110.32 MPa. What would be the ratio of the outside diameter to inside diameter?
If the allowable shear stress is 42 MPa and the allowable angle of twist is 2.5o, what is the maximum permissible torque?
A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so as not to exceed a shearing stress of 42 MPa and an angle of twist of more than 5 degrees in a length of 3 meters. G = 83 GPa
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
What is the minimum diameter of a solid steel shaft that will not twist through more than 3˚ in a6-m length when subjected to a torque of 15 KN-m? What maximum shearing stress isdeveloped? Use G=85 GPa.