please explain and dont use aiQ1 a) If a 36MHz crystal drives the standard 8051, what is the period of one clock pulse? b) Calculate the period (duration) to execute the instruction "MUL AB."
Q: From the following block diagram convert to a Flux diagram, and get its transfer function using…
A: Given block diagram is,Asked to find the transfer function by converting the block diagram to flux…
Q: This is a practice question from the Signal and Systems course of my Electrical Engineering Program.…
A: a) -wb) 7c) 4πd) 5.5e) 38/3f) AttachedExplanation:Since phase of real signal is zero, X(jw) has 0…
Q: Using Multisim, please design and build a complete DC power supply prototype for North America…
A: Hence , we have designed the circuit as per the requirement.Explanation:Question Overview: Here we…
Q: Using Kirchhoff's rules find the the current 11 (3 decimal places) Use any method to solve the…
A: KVL stands for Kirchhoff's Voltage Law. It is a fundamental principle in electrical circuit analysis…
Q: This is a practice question from the Signal and Systems course of my Electrical Engineering Program.…
A: (a) The Fourier transform of the signal. x(t)=sin(2πt+4π) is X(ω)=jπej4πδ(ω−2π)−jπe−j4πδ(ω+2π)…
Q: For the underdamped circuit shown in Fig. P7.110, determine the voltage v(t) if the initial…
A: The given circuit isThe initial conditions on the storage elements are ⇒iL(0)=1 A.⇒vC(0)=10 V.We…
Q: + 4 + + -18. (All dimensions in centimeters) Figure P3.10 Electromagnet for Problem 3.10. 17 + T…
A: This is a transformer question
Q: 1.24 The voltage across a element varies with time as 5(t-2)² V. A current of 2 A enters the +ve…
A: In this question, we need to determine the power delivered to the element at time t=0.8s.
Q: - 2.30. Compute the convolution x(t) *v(t) for ∞ <t< ∞, where x(t) = u(t) + u(t − 1) – 2u(t + 1) −…
A:
Q: Im not sure how to use Laplace transform to solve this circuit. Thanks.
A: The equation of the output voltage is given in the steps when t≥0 .Explanation:
Q: what is the scheme of the conductivity electrode
A: The conductivity electrode is a critical component in measuring the conductivity of a solution,…
Q: Obtain Vo for each of the op amp circuits in Fig. 5.47.
A: In the given circuits the value of the output voltage needs to be calculated.
Q: Find the inverse Laplace transform of: 2s+26 V(s) = 5(s² +48 +13)
A: The Laplace transform is a mathematical technique used to analyze linear time-invariant (LTI)…
Q: What kVA rating is required for a transformer that must handle a maximum load current of 8 A with a…
A: GIven the maximum load current and secondary voltage and required to find the kVA rating.
Q: Find ix using superposition.
A: The current ix is ix= -0.75 amps.Explanation: SUPERPOSITION THEOREM:In any linear active bilateral…
Q: 1. A forward bias of 0.7 V causes a current of 2mA to flow through a diode. What is the reverse…
A: Diode is a two-terminal semiconductor device that allows current to flow in one direction only. It…
Q: Consider a causal stable LTI system with transfer function H(s) = = 82-2s+2 (s²+4s+5)(s+1)* a) Draw…
A: A pole-zero plot of a transfer function is a graphical representation used in control system…
Q: A distortionless cable is 4 m long and has a characteristic impedance of 60 2. An attenuation of…
A: Below is the clarified and detailed explanation for above tricky question.....if you are ok with my…
Q: 2. Consider a sub-stream i of departures that is generated through Bernoulli splitting of a main…
A: According to the question, consider a sub-stream 'i' of departures that is generated through…
Q: 3. A source of information produces equaiprobable blocks of 4-bits. The encoder circuit adds an even…
A: The input-output relationship of an encoder circuit is represented by an encoder table. This makes…
Q: Problem 1 The RLC circuit below has zero voltage in the capacitor and zero current in the inductor…
A: Refer to the given problem,When network goes into steadty state. In steady state for DC excitation…
Q: For the circuit in the following figure, obtain the transfer function Vo(@)Vi(@). Identify the type…
A: The given question is solved in step by step process.Explanation:When two impedances Z1 and Z2 are…
Q: If i¸ (t) -2 u(t) A in the circuit shown in Fig. 16.39, find the value of i,(t). io(1) i,(t) 1 H 202…
A: Given:a circuit,with we need to determine:the value of i0(t).
Q: 1. For the continuous-time periodic signal x(t) below, determine the fundamental period To and…
A: All the parts of the given question have been explained in detail . If any doubt please feel free to…
Q: Find the Power by the 4... resistor. 4... 12.00 6A ↑ 2 2 2000 2 12000
A:
Q: Answer all questions, 1) Answer True or False and correct the error (4 ONLY): 1. Propagation delay…
A: Some statements are given and we need to tell whether the statements are true or false.Also we need…
Q: Si 0.7v lov = R = 1 K~ which Birde is 0V he 0.3v ON for ол ble Circuit and why ?
A: Given:a circuit,we need to find:which diode will turn ON and why?
Q: Problem 2 (a): Match each ODE to its corresponding step response. All initial conditions are zero.…
A: Given diagrams are,Asked to match the system with corresponding step response.Note: “Since you have…
Q: A 15 KVA, 10.8 KV/240-V, 60 Hz, single-phase conventional transformer is supplying 12 KW of power to…
A: A single-phase conventional transformer is a type of electrical transformer that operates with a…
Q: Using mesh analysis, calculate the mesh currents I1 and I2 of the network. Use the resistor values…
A: IR1 = I1 = 6.349206349mA IR2 = I2 = 5.627705628mA IR3 = I1 - I2= 0.7215007215mAExplanation: Thank…
Q: B/IA certain TTL gate has ΛΗ -20 μΑ, IL=0.1 mA, IOH=0.4 mA and IOL-4 mA. Determine the input and…
A: Please go through the below attachment for a detailed explanation. If you have any queries, please…
Q: 4 V IV 50 45 40 35 30 25 20 15 10 5 0 distance [cm] Zo = 602 ZL A 60 lossless line terminated by…
A: Please go through the below attachments for a detailed explanation. If you have any queries, please…
Q: A screen, having a Screening Effectiveness (S) of 31.62 at 100 MHz, is located 5 m from a 2 cm…
A: According to the question, a screen, having a Screening Effectiveness (S) of 31.62 at 100 MHz, is…
Q: please help me with 2.30
A: By using properties of convolution and definition of convolution we can solve all…
Q: 8. Consider the (7,3) systematic cyclic code with g(x) = x²+ x³+ a) Code table & min. Hamming…
A: According to the question, consider the (7,3) systematic cyclic code with g(x) = x4 + x3 + x2 + 1.…
Q: B//Define the following: 1- Unit load 2-Noise immunity 3-E2CMOS
A: Load refers to the electrical impedance or resistance that a device or component presents to a…
Q: how do this
A: The objective of this question is to understand how a sinusoidal signal is quantized by a midtread…
Q: can you please explain how we do the d) section
A:
Q: For the message signal m(t) shown below, sketch (PFM(t) and (PPM(t), given o=2x107, k₁ = 10*π, and…
A: According to the question, for the given signal m(t) as shown belowWe need to sketch FM signal and…
Q: In a certain magnetic circuit, the core is represented two reluctances as shown below. Assume a…
A: In this question, we need to determine the current in the circuit to produce the given flux. We…
Q: In figure, R3 = R₁ = 5.6k, and R₂ = 220k. a) If V₁ = 27mV and V2 = 0mV, what is V Vout? b) If V2 is…
A: In an ideal op-amp , op-amp draws zero internal current due to high input impedance. The voltage at…
Q: Identify the placement of a webcam/eye in Figure 2 for a Twyman-Green setup.
A: In the schematic diagram of the Twyman-Green interferometer workstation shown in Figure 2, several…
Q: Q6) Calculate the gain of a parabolic antenna of 100% illumination and having a 30° radiation…
A:
Q: 3.17. A 200-turn coil is rotating at a speed of 3600 rpm in a 4-pole generator. The flux per pole is…
A: The given question is solved in step by step process.Explanation:
Q: For a 0.4X-long 50 12 lossless transmission line, find the following quantities (i-v) separately for…
A: below given complete solution brieflyExplanation:Step 1: Step 2:Step 3:Step 4:
Q: 1) The magnetic field intensity in a lossless, non-magnetic medium with H = cos(@t-4z)â (A/m) .Find:…
A:
Q: A lossy transmission line of length 2.1 m has characteristic impedance of 80 + j60. When the line is…
A: A)1) The Value of α is 0.0748 2) The value of β is 0.1315 rad/secB) Zin = (61.4655 + 24.43 j) Ω…
Q: 4. A (9,5) LBC has the correction bits: C1 a1a3+ as C2-C1+24 C3-C2+ a2+ as C4 C3+a4+ a3 + Mod. 2…
A: Given:Correction bits for (9,5) LBC code, we need to find:i) parity matrix of the codeii) generator…
Q: C(s) 5. Using the Mason's gain formula, obtain the closed loop transfer function R(s) for Figure 5.…
A: A transfer function is a mathematical representation that describes the relationship between the…
Q: 2. Find the voltage v(t) and current i(t) in this circuit. The switch closes at time t=0. V₁ = 100 V…
A: The given circuit isWe need to determine the expression of v(t) and i(t) in the circuit.
please explain and dont use ai
Q1 a) If a 36MHz crystal drives the standard 8051, what is the period of one clock pulse?
b) Calculate the period (duration) to execute the instruction "MUL AB."
Step by step
Solved in 1 steps
- dont use ai and please explainQ1 a) If a 16MHz crystal drives the standard 8051, what is the period of one clock pulse? b) Calculate the period (duration) to execute the instruction "MUL AB."A digital wave is received. It says the value for low is 5 V. The system registers it as low from 8V. This system switches On as of 12 V and registers High at 15 V. What is the unacceptable range of the system?1)This multiple choice question from MEASUREMENTS INSTRUMENTATIONS course.just write for me the final answer.
- Good day! Please help me determine the conduction angle in my simulation as well as the delay angle. Please teach me also how to determine it. Thank you! need asap.7 which option is the Q2Q1Qo value given correctly after 14 clock pulses in the following digital circuit?Simulation is NOT required. Please show calculations please. Thank you.
- We want to create a square wave of 50% duty cycle (with equal portions high and low) on the pin P0.0 of the microcontroller 8051 as shown in the following figure. Timer 1 is used to generate the time delay. Write the corresponding assembly Assume XTAL = 11.0592 MHz.Create a circuit diagram for the prototype of "Motion Sensor Light Activator using Raspberry Pi Pico" with a 5w bulb.Note: - Please include the names and values needed (voltages) of the materials on this prototypeDraw the block diagram of a CPU showing the basic units. Explain the functions of each unit shortly.
- Please draw: Circuit diagram (Circuit design) and block diagram they contain (Embedded microcontroller, vibration sensor)For the common-emitter fixed-bias configuration. Determine the level of emitter AC resistance or re with the effect of output resistance ro. Note: a) answers in two decimal places. b) please use your calculator's memory capabilities and only your final answers should be rounded.Calculate Vth