Please show complete solutions. Need asap. The series of bars shown have their diameters from left to right decreasing by 3mm, and have lengths increasing correspondingly by 0.3m. if the leftmost member has a diameter and length of 28mm, 1.8 m, respectively, determine the nodal displacements, member forces and the value of P if the node where P acts undergoes a rightward displacement of 4.5 mm. E=180 GPa for all members. 60 N/mm 90 N/mm 45 N/mm -30 KN P -50 KN

Please show complete solutions. Need asap. The series of bars shown have their diameters from left to right decreasing by 3mm, and have lengths increasing correspondingly by 0.3m. if the leftmost member has a diameter and length of 28mm, 1.8 m, respectively, determine the nodal displacements, member forces and the value of P if the node where P acts undergoes a rightward displacement of 4.5 mm. E=180 GPa for all members. 60 N/mm 90 N/mm 45 N/mm -30 KN P -50 KN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.2P: Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the...

See similar textbooks

Similar questions

Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
For the spring assemblage shown below, determine the displacement at node 2 and the forces in each spring element. Also determine the force F3. Given: Node 3 displaces an amount 8 = 12.5 mm in the positive x direction because of the force F3 and k1 k2 175 kN/m.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
The ABD bracket is supported by a pin at A and the cable DE. Determine the internal forces immediately to the left of the load.Template: (On CD) F= 270 N; M=43.2 N.m; V = 90 N
A rear suspension system for a front wheel-drive vehicle is shown here. Spring EF is offset behind member CD. The normal force due to contact between the wheel and the road is 4200 N. Assume the weight of the wheel and suspension system components is negligible. Determine the magnitude of the member CD. Is the member in tension or compression? Determine the support reactions at A. Determine the unstretched length of the spring EF given a spring constant of 150 kN/m.
Use the method of sections to find the true magnitude and direction in bar DB of the truss. Hint (Joint C is in equilibrium)
The 20 mm diameter steel shaft AB is attached into the rigid wall at B and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. If the downward force P will produce a 50 mm vertical displacement at the free end of lever AC, determine the force P if G = 83 GPa.
Please show the complete solution and draw the free body diagram correctly
PROBLEM: Determine the forces in each member using any methoddiscussed in your theory of structures/mechanics. Using Software is notallowed. Show complete solution and tabulate your answers indicatingwhether it is compression or tension. Use Pn = 205 kN, Po = Zero. a) From the Problem and the image , Design one tension member, use either a double angle of a wt section. Check its adequacy using 1 line of bolts (three bolts in a line spaced at 75mm on centers) Assume a bolt diameter from 16-22mm. Use A 36 for all steel. Neglect block shear.
A RIGID BAR "AB" ATTACHED TO TWO VERTICAL RODS IS HORIZONTAL BEFORE LOAD P IS APPLIED. DETERMINE THE VERTICAL MOVEMENT OF POINT CIF THE MAGNITUDE OF P IS 60 KN.
An element made of AISI 1020 CD steel is shown, but to shape it, it had to be machined. It must have a reliability of 99.9999%.It is subjected to the loads P₁= 200 pounds and P₂= 400 pounds; In others, the force in the "z" direction does not act, but the force in "y" remains with the same magnitude, but is completely reversed, in the positive and negative sense of the "y". Determine:to. The critical point of the system and for this establish the state of effort. Explainb. Apply Mohr's circle to the critical stress state and obtain σ1, σ2 and tmaxC Determine the safety factor and explain.