plz solve q3 part b 3. (a) Shown in figure 2 is a sectioned view of an Eddy Current dy-namometer. Define the items labelled A to E, and making ref-erence to these items, describe the principles by which the dy-namometer measures torque and power - include any relevantformulae in your answer.BAEFigure 2: Eddy Current Dynamometer(b) A 2498c.c turbocharged four cylinder SI engine produces 323NMof torque at 8200rpm while consuming 95litres of petrol perhour. The petrol has density of 740kg/m. The higher calorificvalue for the petrol is 46.4M J/kg while the lower calorific valueis 43.4M J/kg. Calculate the following performance measures;i Brake Powerii Brake Mean Effective Pressurei Brake Specific Fuel Consumptioniv Thermal Efficiency(c) Describe a feasible test procedure to obtain an estimate of theindicated mean effective pressure of an engine. Include detailsof the theory which underpins the test procedure, and any mea-surement problems or sources of inaccuracy.

(b) (i) To find: The break power. Given: The volume is V=2498 cm3. The torque is T=323 Nm. The…

Answered: plz solve q3 part b

Engineering

Mechanical Engineering

plz solve q3 part b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piezoelectric actuator is made from a stack of 20 square piezoelectric pads, each 10mm squarewith a thickness of 2mm? Calculate the maximum displacement when 1kV is applied given that d33=100×10-12 C/N, er = 50 and Y = 50GPa.
Q1. Long-shunt generator delivers a load current of 30 A at 220 V. It has armature and shunt field resistances of 0.050, 2000 respectively: A- calculate the generated emf, the copper loss in armature, shunt field loss and the total copper loss. B-if the iron and friction loss is 1000W. Calculate the electrical efficiency, mechanical efficiency, commertial efficiency and maximum efficiency. (Armature reaction may be neglected) Q2. A 220V, 4-pole, lap-connected, shunt motor with 800 conductors in armature slots. The armature and shunt field resistance are 0.62 and 2200 respectively. The motor runs to supply load with 8000W and draw current (50amps) from the mains. The flux per pole is 25mWb A- Calculate the gross torque developed by the armature, the shaft torque (useful), and the lost torque. B- Calculate the gross power developed by the armature, the iron and friction lost power, mechanical efficiency, electrical efficiency, and the overall efficiency. Armature reaction may be…
pleassssse solve question 9, statics
The collector leakage current in a transistor is 300 μA in CE arrangement. If now the transistor is connected in CB arrangement, what will be the leakage current? Assume β = 120. (2) For a certain transistor, IB = 20 μA; IC = 2 mA and β = 80. Calculate ICBO. (3) In a transistor, IB = 68 μA, IE = 30 mA and β = 440. Determine α rating of the transistor. Then determine the value of IC using both the α rating and β rating of the transistor.
A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
A shunt generator delivers 195 A at terminal p.m. of 250 V. The armature resistance and shunt field resistance are 0.02 ohm and 50 ohm respectively. The iron and friction losses equal 950 W. Find (a) E.M.F. generated (b) Cu losses (c) output of the prime mover (d) commercial, mechanical and electrical efficiencies.
. On a nautical chart their are times that their are more than one Compass Rose what is the main reason due to what condition? Is the condition variation or magnetic variation?
Why is the Fourier transform used in reciprocal space in Bragg's Law?
A three-cylinder four-stroke engine running at 750 revolutions per minute (rm) consists of cylinders each with a bore diameter 18.50 cm and a piston stroke length of 40.20 cm. During engine testing when the engine is running at 750 revolutions per minute (rpm), a pressure-volume (p-v) indicator diagram is generated and has a mean net area of 6.50 cm? and a diagram length of 3.25 cm. The pressure scale on the indictor diagram is set to 180 kN/m? per cm. Calculate the indicated power in kilowatts (kW) developed by this engine and give your answer to 2 decimal places
Calculate the Resistance , if the RTD temperature is 2506.8 oC and Sensitivity is 9.6 oC/ohm
A Chromel-Constantan thermocouple is used to measure the temperature of water in heating bath. The reference temperature was 0 °C. The voltmeter measures a voltage difference ∆E of 2.5 mV. What is the temperature of the water ?
5. 30,000 kW at power factor 0-8 lagging is being transmitted over a 220 kV, three-phase transmission line. The length of the line is 275 km and the efficiency of transmission is 90%. Calculate the weight of copper. Also calculate the weight of copper had the power been transmitted over a single-phase transmission line tor the same line voltage and losses. ASsume that the resistance of 1km long conductor and 1sq.cm is 0.173 andspecific gravity of copper is 8-9.