Polymerase Chain Reaction (PCR) is an essential technique for the study of DNA. PCR uses a DNA polymerase enzyme from Thermophilus aquaticus to amplify DNA extracted from any sample. In order for the reaction to work, researchers must transfer microliters of sample to the reaction vessel for PCR. If a researcher has a DNA sample with a concentration of 0.029 micrograms per microliter, how many microliters of DNA must be transfered to conduct a 50 microliter reaction if the final concentration should be 4.6 nanograms per microliter? Report your answer to two decimal places using normal decimal notation (e.g. 0.5, not 5.0e-1)

Polymerase Chain Reaction (PCR) is an essential technique for the study of DNA. PCR uses a DNA polymerase enzyme from Thermophilus aquaticus to amplify DNA extracted from any sample. In order for the reaction to work, researchers must transfer microliters of sample to the reaction vessel for PCR. If a researcher has a DNA sample with a concentration of 0.029 micrograms per microliter, how many microliters of DNA must be transfered to conduct a 50 microliter reaction if the final concentration should be 4.6 nanograms per microliter? Report your answer to two decimal places using normal decimal notation (e.g. 0.5, not 5.0e-1)

Chemistry for Engineering Students

4th Edition

ISBN:9781337398909

Author:Lawrence S. Brown, Tom Holme

Publisher:Lawrence S. Brown, Tom Holme

Chapter3: Molecules, Moles, And Chemical Equations

Section: Chapter Questions

Problem 3.108PAE: 3.108 As chip speeds increase, the width of the interconnects described in Problem 3.107 must be...

See similar textbooks

Similar questions

The volume of the mixture prepared by taking 1.158 mol and 0.842 mol of water and ethanol, respectively, was measured as 68.16 cm3 at 25 ° C.Since the partial molar volume of water in the mixture is 16.98 cm3 / mol, find the partial molar volume of ethanol.Since the densities at 25ᴼC for pure water and ethanol are given as 0,9970 g / cm3 and 0,7852 g / cm3, respectively, find the volume change during the preparation of the mixture and interpret the result. (MSu: 18 g / mol; Methanol = 46 g / mol)
absorbance data that you have obtained while doing an experiment studying the diffusion of potassium permanganate into solutions of water. This diffusion experiment was conducted at three temperatures. Calculate the diffusion rates for each of these temperature conditions. Write your answer in standard notation and use 3 digits past the decimal point Diffusion Rate 4°C = __________________ Diffusion Rate 22°C = _________________ Diffusion Rate 37°C = _________________ To show how you calculated the diffusion rates for these temperature - What absorbance values did you choose to calculate the slope for the 37°C condition? __________________ and ________________________ Time (min) 4°C 22°C 37°C 0 0.024 0.108 0.081 5 0.048 0.144 0.221 10 0.069 0.196 0.321 15 0.088 0.224 0.424 20 0.086 0.234 0.580 25 0.089 0.248 0.683
You work in a research organization that is looking for markers of various diseases that can be used as a diagnostic for the disease. It has been reported in the past that high levels of Cu are found in the sweat of people with cystic fibrosis. One of the research projects is focused on looking for high levels of Cu in samples that can be obtained non-invasively such as saliva, sweat, hair, nails, etc. The lab will analyze large samples for Cu. What instrument would you recommend purchasing to support this work, Atomic absorption spectrophotometer or an inductively coupled plasma atomic spectrophotometer? Explain the basis for your decision.
How sedimentation rate got influenced by particle mass ?
A manometer was connected to a bulb containing nitrogen under slight pressure. The gas was allowed to escape through a small pinhole, and the time for the manometer reading to drop from 65.1 cm to 42.1 cm was 18.5 s. When the experiment was repeated using a fluorocarbon gas, the same fall took place in 82.3 s. Calculate the molar mass of the fluorocarbon.
A student performed the experiment described in this module, using 7.00 mL of a 1.8% H2O2 solution with a density of 1.01 g mL-1. The water temperature was 20 ° C, and the barometric pressure in the laboratory was 30.02 in. Hg. After the student immersed the yeast in the peroxide solution, she collected 45.1 mL of O2. (11) Calculate the percent error for the experiment.
there is a set of absorbance data that you have obtained while doing an experiment studying the diffusion of potassium permanganate into solutions of water. This diffusion experiment was conducted at three temperatures. Calculate the diffusion rates for each of these temperature conditions. Write your answer in standard notation and use 3 digits past the decimal Diffusion Rate 4°C = __________________ Diffusion Rate 22°C = _________________ Diffusion Rate 37°C = _________________ To show how you calculated the diffusion rates for these temperature - What absorbance values did you choose to calculate the slope for the 37°C condition? __________________ and ________________________ Time (min) 4°C 22°C 37°C 0 0.024 0.108 0.081 5 0.048 0.144 0.221 10 0.069 0.196 0.321 15 0.088 0.224 0.424 20 0.086 0.234 0.580 25 0.089 0.248 0.683
Soil vapor extraction (SVE) is used to remove volatile or-ganic pollutants, such as chlorinated solvents, from soil at haz-ardous waste sites. Vent wells are drilled, and a vacuum pump is applied to the subsurface. (a) How does this remove pollutants?(b) Why does heating combined with SVE speed the process?
What is the simplest CGS unit for "poise"?
Explain the difference between random sampling and haphazard sampling as used in Analytical chemistry.
Measurements of boiling temperatures of samples of a liquid (°C) are given below: 78.4 79.0 78.8 79.2 78.6 Calculate the meanCalculate the modeCalculate the standard deviation
A student performed the experiment described in this module, using 7.00 mL of a 1.8% H2O2 solution with a density of 1.01 g mL-1. The water temperature was 20 ° C, and the barometric pressure in the laboratory was 30.02 in. Hg. After the student immersed the yeast in the peroxide solution, she collected 45.1 mL of O2. (11) Calculate the percent error for the experiment. What is the observed molar volume?