portion of the conduit above the roof cannot exceed what lengh?The total length of condut from DS to HiAC unit is so To meet NEC code theIn the figure below, a conduit with a balanced three phase supply runs tromadisconnect switch (DS) located in an office area to the HVAC unit on te root28Roof lineHVACDisconnect Swb.d.10t

Given figure is shown below. The total length of conduit from disconnect switch (DS) to HVAC unit…

portion of the condut above the roof cannot exceed what lengh In the figure below, a condut with a balanced three-phase sucply us troma The total leng of conduit trom DS to HAC unit is 90 To met NEC cod the disconnect swtch DS located in an office area to the HAC unt on the oot 28 Roof line HVAC Disconnect Sw 10

portion of the condut above the roof cannot exceed what lengh In the figure below, a condut with a balanced three-phase sucply us troma The total leng of conduit trom DS to HAC unit is 90 To met NEC cod the disconnect swtch DS located in an office area to the HAC unt on the oot 28 Roof line HVAC Disconnect Sw 10

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter5: Conductor Identification, Switch Control Of Lighting Circuits, Bonding/grounding Of Wiring Devices, And Induction Heating

Section: Chapter Questions

Problem 26R

See similar textbooks

Similar questions

In the conduit diagram shown in attached picture, determine how many wires are in each conduit between each piece of equipment. Identify each wire terminal connection and the quantity of wires, as shown in the example, above the disconnect
In the conduit layout shown in picture attached, determine how many wires are contained in each conduit between each piece of equipment. Identify each wire with a proper terminal marking, as shown in the example, above the disconnect switch.
5. How many system bonding jumpers normally are there for a separately derived system that's grounded? A. ThreeB. TwoC. One D. Zero 6. How many grounded neutral conductors are in a 208Y/120 volt, 3-phase, 4-wire system? A. ThreeB. TwoC. One D. Four 7. Which of the following are sometimes installed as an emergency system, legally required standby system, or optional standby power system for a building or structure? A. GeneratorsB. Surge protection devices C. Surge arrestersD. Transformers 8. If the system bonding jumper in a DC system is a screw, what color must the screw be? A. WhiteB. RedC. Orange D. Green 9. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct? A. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect. B. There's no need for service equipment or a panelboard in the separate building.C. A ground electrode must…
A 15-ampere, 120-volt lighting branch circuit would be 12 amperes maximum connected load. true or false
Are double locknuts an acceptable bonding method for Class 1, Division 1 Hazardous locations? If not, list an acceptable method, backing up your answer with a code citation.
19. Which of the following is an approved disconnecting means for a feeder or branch circuit supplying a separate building or structure? A. Bonding locknutB. PanelboardC. Circuit breakerD. Overcurrent device
17. In an air compressor system, the distribution piping can be bonded using theA. equipment grounding conductor supplying the air compressor's motor.B. grounding electrode driven near the compressor motor.C. grounded neutral conductor.D. equipment grounding conductor at the service entrance. 18. Which of the following would help avoid the choke effect in grounding electrode conductors?A. Installing a main bonding jumper B. Using an approved polyvinyl chloride conduitC. Applying solder to the connection D. Using bonding bushes on the ends of the raceway
The frames of ranges, wall-mounted ovens, counter-mounted cooking units, and clothes dryers under the conditions permitted for existing installations, ___ permitted to be connected to the grounded circuit conductor. Select one: a. shall not be b. can not c. may be d. shall be
It is generally understood that grounding and bonding together all metal parts of an electrical system and the metal shield of the cable television cable to the same grounding reference point in a residence will keep both systems at the same voltage level should a surge, such as lightning, occur. Therefore, if the incoming cable that has been installed by the CATV cable company installer has the metal shield grounded to a driven ground rod, does this installation conform to the NEC? ___________
When installing a surge arrester at the service of less than 1000 volts, the grounding conductor shall be connected to ______. the grounded service conductor the grounding electrode conductor III. the grounding electrode for the service the equipment grounding terminal in the service equipment (a.) I & II only (c.) III & IV only (b.) I & III only (d.) I, II, III or IV
16. The _______ point is where the facilities of the serving utility and the premises wiring connect.A. groundedB. neutralC. serviceD. bonding
The ends of conduit must be reamed and entries to boxes and accessories must be bushed in order, why?