Which of the following statements about bonding is true? A. The strike terminals of a lightning protection system must be bonded to the building or structure grounding electrode system. B. Bonding requirements on the supply side of the service disconnect are less restrictive. C. Wire-type supply-side bonding jumpers are usually short in length and installed from the service-entrance conductor to a single raceway. D. Metal water piping systems have one set of rules in the National Electrical Code.

Which of the following statements about bonding is true? A. The strike terminals of a lightning protection system must be bonded to the building or structure grounding electrode system. B. Bonding requirements on the supply side of the service disconnect are less restrictive. C. Wire-type supply-side bonding jumpers are usually short in length and installed from the service-entrance conductor to a single raceway. D. Metal water piping systems have one set of rules in the National Electrical Code.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 10R: It is generally understood that grounding and bonding together all metal parts of an electrical...

See similar textbooks

Similar questions

It is generally understood that grounding and bonding together all metal parts of an electrical system and the metal shield of the cable television cable to the same grounding reference point in a residence will keep both systems at the same voltage level should a surge, such as lightning, occur. Therefore, if the incoming cable that has been installed by the CATV cable company installer has the metal shield grounded to a driven ground rod, does this installation conform to the NEC? ___________
A Type NM cable carries a branch circuit to the outside of a building, where it terminates in a metal weatherproof junction box. From this box, a short length of EMT is installed upward to another metal weatherproof junction box on which is attached a cluster of outdoor floodlights. The first box is located approximately 24 in. (600 mm) above the ground. To Meet Code, do the metal boxes and metal raceway have to be grounded? Yes _______________ No _______________ NEC _______________.
Which of the following is a term missing from the National Electrical Code but used by manufacturers of equipment that's suitable for use as service equipment? Micro-grid  Selective coordination Neutral disconnect link Grounding triad The _______ is required to be connected to the grounded conductor of the sensitive electronic system on the line side of the separately derived system disconnecting means. main bonding jumper  equipment grounding terminal bus neutral ground strap neutral disconnect link
17. In an air compressor system, the distribution piping can be bonded using theA. equipment grounding conductor supplying the air compressor's motor.B. grounding electrode driven near the compressor motor.C. grounded neutral conductor.D. equipment grounding conductor at the service entrance. 18. Which of the following would help avoid the choke effect in grounding electrode conductors?A. Installing a main bonding jumper B. Using an approved polyvinyl chloride conduitC. Applying solder to the connection D. Using bonding bushes on the ends of the raceway
Are double locknuts an acceptable bonding method for Class 1, Division 1 Hazardous locations? If not, list an acceptable method, backing up your answer with a code citation.
6. Which type of cable would you use to connect two buildings in an office installation?A. Buried loose-tube cableB. Aerial armored cableC. OFNP cableD. Tight-buffered cable
14. If the total circular mil area of the largest ungrounded service-entrance conductor for a service is 2000-kcmil copper, what is the minimum size required for a wire-type main bonding jumper for the service? a) 4/0 AWG copper b) 250-kcmil copper c) 350-kcmil copper d) 500-kcmil copper 15. The minimum-size grounded conductor for a service supplied by a grounded system shall not be smaller than the minimum size required for a(n)______. a) Equipment grounding conductor b) System bonding jumper c) Ungrounded conductor d) Grounding-electrode conductor Note: answer both the questions with proper explanation. As per bartleby honor code I can submit 3 questions. So please answer both
10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
analyse the rating of wires/ cables and mcb used for different types of loads
6. Which of the following is a condition that a liquidtight flexible metal conduit must meet in order to be suitable as an equipment grounding conductor? A. The conduit is terminated in listed fittings.B. For trade sizes 3/4 through 1 1/4, the conduit conductors contained in the conduit are protected by overcurrent devices rated at 20 amperes or less.C. The combined length of the conduit and other tubing and conduit in the same ground-fault path exceeds six feet. D. For trade sides 3/8 through 1/2, the circuit conductors contained in the conduit are protected by overcurrent devices rated not more than 60 amperes. 7. You're going to connect a surge protection device to a separately derived electrical system. In this situation, the surge protection device should be connected at A. the load side of the first overcurrent protection device. B. the input to the transformer's primary winding.C. the end of the shortest branch circuit.D. the first connected IT cabinet. 8. What is another term…
5. If a separate, wire-type equipment grounding conductor (EGC) is used for any reason, the EGC of a grounding-type receptacle must be connected to which of the following?A. The grounding terminal bar outside the service equipment enclosure in a grounded systemB. An EGC that's part of another branch circuit that originates from where the branch circuit for the receptacle originatesC. Any accessible point on the grounding electrode conductorD. The service conductor outside the service equipment enclosure in an ungrounded system
In the conduit diagram shown in attached picture, determine how many wires are in each conduit between each piece of equipment. Identify each wire terminal connection and the quantity of wires, as shown in the example, above the disconnect