4G :12:30i sct.edu.omTHAL LAMIVI IVIILAIUU IV y.Process Group 3Question 13Not yet answeredMarked out of 1.00P Flag question_ is used togive the counter turning cycleof CNC machine.O a. G96O b. G00C. GO1d. G73Previous pageNext pagePrevious activity( Dip. ProjectII

Option d is correct answer : d. G73

Answered: Previous activity Dip. Project

Engineering

Mechanical Engineering

Previous activity Dip. Project

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.19P

See similar textbooks

Similar questions

What would be the technical classifi cation of the followingturbomachines: (a) a household fan, (b) a windmill, (c) anaircraft propeller, (d ) a fuel pump in a car, (e) an eductor,(f ) a fl uid-coupling transmission, and (g) a power plantsteam turbine?
please solve it i need urgent A naturally-aspirated (NA) oil engine (i.e., a slow-speed CI Engine) which produces one power pulse in two revolutions of its crankshaft is to be designed to operate with the following characteristic at sea level where the mean atmospheric conditions are Pa = 101325 N/m2 and ta = 17°C. The value of gas constant of air is Ra = 0.287 kJ/(kg·K). Gross brake power, Wb, gross = 300 kW Volumetric efficiency, hvol = 80% Brake specific fuel consumption, sfcb = 255 g/(kW·h) Actual air-to-fuel ratio, (A/F)act = (m a / m f )act = 17:1 Angular speed of the shaft, w = 125 rad/s Calculate: (i) The required engine capacity Vs, total in cc (cm3), as well as in litres (L); Vs is the swept volume, and (ii) the brake mean effective pressure ( Pbm ). The engine is fitted with a supercharger (SC) so that it may be operated at an al- titude, z, of 3000 m (above sea level) where the atmospheric pressure (Pa) in N/m2 is determined from the following relation: Pa =…
(11) A 120cm diameter diamond circular blade, mounted on a pulley-driven steel shaft, is requiring a blade peripheral linear speed of 45m/s. Motor drive is 100kW @ 1,200rpm with 150mm drive pulley. Determine: (a) the shaft rpm to attain blade peripheral speed required; (b) the shaft diameter; (c) the shaft pulley diameter.
ANSWER ASAP. WILL UPVOTEEEEEEEEEEEEEEEEE
An ice plant produces 10 tons of ice per day at 0°C using water at room temperature of 27°C. Estimate the power rating (Electrical Power consumed by the motor to run compressor) of the compressor-motor, if the C.O.P. of the plant is 3.0 and overall electro-mechanical efficiency (η) is 91%. Note: Latent heat of ice is 335 kJ/kg, Cp = 4.18 kJ/kg.K.
Diesel Cycle:16. A Diesel Cycle has a volume displacement of 0.95 m3 and the volume at during heat rejection is 1 m3. Determine the volume at the end of heat addition if the cut-off ratio 2.25.
The performance data of a water pump follow the curve fit Havailable = H0 − aV.2 , where the pump’s shutoff head H0 = 7.46 m, coefficient a = 0.0453 m/(Lpm)2 , the units of pump head H are meters, and the units of V. are liters per minute (Lpm). The pump is used to pump water from one large reservoir to another large reservoir at a higher elevation. The free surfaces of both reservoirs are exposed to atmospheric pressure. The system curve simplifies to Hrequired = (z2 − z1) + bV.2 , where elevation difference z2 − z1 = 3.52 m, and coefficient b = 0.0261 m/(Lpm)2 . Calculate the operating point of the pump (V.operating and Hoperating) in appropriate units (Lpm and meters, respectively).
In a cyclic comprising of air compressor and expansion, workdone by a prism during the compression stroke is 9.2KJ and the heat rejected to the surrounding is 50KJ. During the expansion stroke workdone by air on the prism is 8.4KJ. a) Determine the quality of heat transferred to or from the system. Tullow oil has discovered a large volume of crude deposit at Cape-3-Point along the western coast of Ghana after years of intensive exploration. In the Company’s bid to start exploration, Green Ghana an environmental protection NGO took Tullow to court to prevent the Company from embarking on the said project citing numerous environmental concerns. b) As an energy and sustainability expert, what do you think are the side effects of the project and their remedies? A cooling water pump is operating at a speed of 1800rpm. Its flow rate is 1800L/minutes at a head of 14.4m and the power of the pump is 45kw. c) Determine the power required if the pump speed is increased…
A six cylinder four stroke diesel engine with 76mm bore x 89mm stroke consumed 12.5 kg of fuel per hour with a heating value of 52,120KJ/kg and 252kg of air at 15.6°C per hour. If the generator efficiency is 90% with 26 poles, determine the generator speed(rps).
What is the engine speed (in rpm) required for good volumetric efficiency for an engine with two inlet and two exhaust valves, bore of 0.086 m, stroke of 90 mm, inlet air temperature of 330 K, exhaust temperature of 900 K and inlet valve diameter 30 mm (each). Assume specific heat ratio =1.37, R = 287 J/kg.K and an average inlet flow coefficient 0.4. Select one: a. 7013 O b. 6350 O c. 7847 O d. 4620 e. 9202
The overall engine heat transfer rate (kW) for a single cylinder engine with a 0.09 m bore and stroke, average combustion gas temperature of 980 K, coolant temperature of 345 K, and fuel-air flow rate of 1.8 *10-2 kg/s is: (Assume the thermal conductivity is 0.062 W/m.K and the dynamic viscosity is 19*10-6 N.s/m2). Select one: O a. 26 O b. 46 O c. 36 O d. 66 O e. 56
(a) sigma max,min =+- 10.6 lodi Tau max = 5.35 kpsi (b) vb= -0.0102 in, wb= 0.0234 in