Print Reading for Industry282ClassNameDateIndustry Print Exercise 13-1Refer to the print PR 13-1 and answer the questions below.1. Are the datums identified following the current standard or an older standard?2. Before datum A can be used as a datum, what qualification must it meet?3. What feature is used to establish datum B?4. Why do the coordinate location dimensions have boxes around them?5. Do any of the feature control frames specify a bonus tolerance?6. The depth (front-to-back) of the part has a tolerance specified by the title block as .02" (t.01").Nevertheless, the front surface must still be parallel to the back by what amount?7. What is the MMC of datum feature B, which has a title block tolerance specification of .010" (t.005")?Review questions based onprevious units:8. What is the part number of this print?9. How many threaded holes are there on this part?10. What is the radius of the four corners of this part?11. What type of metal should be used for this part?12. What is the size tolerance on the four largest counterbore diameters?13. What is the overall height, width, and depth of this part? HW14. What type of section view is the right side view?15. What type of representation is used to show the threads in the section view? Geometric Dimensioning and Tolerancing283898 2908(000893 386898 2Print supplied by MASCO CorporatioPR 13-1. Cylinder Union Lower Support.8006.61O.010-A-3.311.25DRILL THRU & C'BOREFOR 3/8-16 S.H.C.S.(FROM OPPOSITE SIDE)4 PLACESDRILL & REAM THRUFOR 1/4 DIA DOWEL S.F.4 PLACES.78.014 M A.002 A B.25L..2.9212.34296 23.341.5854X 1.0318004.47.171( 000 ).454.7584X 1.5007/1.501 o.002 A4X R.44- 5/8-18 TAP4 PLACES.562 THRUØ.010 AB0050-B-800SECTION A-A1 REQD.DO NOT SCALE ORAWINGTHIS DRAVING AND THE INFORMAYION CONTAINEDTHEREON ARE THE FROPERTYOTHERS AND MAY 8SED ONLY POR TE FURPOSE OF ENABL INO THE PARTYTO WHOM IT HAS BEEN LOANED TO QUOTE ON OR PILL AN OR0ER FOR MASCOUNLESS OTHERWISE SPECIFIEDLAYOUT NAME ORAFTMASCOA CORPORATIONANGUL AR DIM- +/-.052-PLACE DEC. -018-PLACE DEC. -.005 SHARP EDGES A .03VIEWS DISP.DATE ISSUEDNAME:DATE:TITLE9200-/+ 30 d-MATERIAL:MASTECH CONTRL DIVISIONLOWER SUPPORTCYLINDER UNIONORAWN A ADRIANSON01/31/6061-T6 ALUMINUMDESTROYPREVIOUS PRINTS217C017CHECKREV DATECHANGE:CHKDFINISHSCALE FULLAPPR

Question
Asked Oct 10, 2019
15 views

I need help answering problems 4, 5, and 6 pertaining to the print provided in the attachment. 

Print Reading for Industry
282
Class
Name
Date
Industry Print Exercise 13-1
Refer to the print PR 13-1 and answer the questions below.
1. Are the datums identified following the current standard or an older standard?
2. Before datum A can be used as a datum, what qualification must it meet?
3. What feature is used to establish datum B?
4. Why do the coordinate location dimensions have boxes around them?
5. Do any of the feature control frames specify a bonus tolerance?
6. The depth (front-to-back) of the part has a tolerance specified by the title block as .02" (t.01").
Nevertheless, the front surface must still be parallel to the back by what amount?
7. What is the MMC of datum feature B, which has a title block tolerance specification of .010" (t.005")?
Review questions based on
previous units:
8. What is the part number of this print?
9. How many threaded holes are there on this part?
10. What is the radius of the four corners of this part?
11. What type of metal should be used for this part?
12. What is the size tolerance on the four largest counterbore diameters?
13. What is the overall height, width, and depth of this part? H
W
14. What type of section view is the right side view?
15. What type of representation is used to show the threads in the section view?
help_outline

Image Transcriptionclose

Print Reading for Industry 282 Class Name Date Industry Print Exercise 13-1 Refer to the print PR 13-1 and answer the questions below. 1. Are the datums identified following the current standard or an older standard? 2. Before datum A can be used as a datum, what qualification must it meet? 3. What feature is used to establish datum B? 4. Why do the coordinate location dimensions have boxes around them? 5. Do any of the feature control frames specify a bonus tolerance? 6. The depth (front-to-back) of the part has a tolerance specified by the title block as .02" (t.01"). Nevertheless, the front surface must still be parallel to the back by what amount? 7. What is the MMC of datum feature B, which has a title block tolerance specification of .010" (t.005")? Review questions based on previous units: 8. What is the part number of this print? 9. How many threaded holes are there on this part? 10. What is the radius of the four corners of this part? 11. What type of metal should be used for this part? 12. What is the size tolerance on the four largest counterbore diameters? 13. What is the overall height, width, and depth of this part? H W 14. What type of section view is the right side view? 15. What type of representation is used to show the threads in the section view?

fullscreen
Geometric Dimensioning and Tolerancing
283
898 2
908
(000
893 386
898 2
Print supplied by MASCO Corporatio
PR 13-1. Cylinder Union Lower Support.
800
6.61
O.010
-A-
3.31
1.25
DRILL THRU & C'BORE
FOR 3/8-16 S.H.C.S.
(FROM OPPOSITE SIDE)
4 PLACES
DRILL & REAM THRU
FOR 1/4 DIA DOWEL S.F.
4 PLACES
.78
.014 M A
.002 A B
.25
L..
2.921
2.342
96 2
3.34
1.585
4X 1.031
800
4.47
.171
( 000 )
.454
.758
4X 1.5007/1.501 o
.002 A
4X R.44
- 5/8-18 TAP
4 PLACES
.562 THRU
Ø.010 A
B
0050
-B-
800
SECTION A-A
1 REQD.
DO NOT SCALE ORAWING
THIS DRAVING AND THE INFORMAYION CONTAINEDTHEREON ARE THE FROPERTY
OTHERS AND MAY 8SED ONLY POR TE FURPOSE OF ENABL INO THE PARTY
TO WHOM IT HAS BEEN LOANED TO QUOTE ON OR PILL AN OR0ER FOR MASCO
UNLESS OTHERWISE SPECIFIED
LAYOUT NAME ORAFT
MASCO
A CORPORATION
ANGUL AR DIM- +/-.05
2-PLACE DEC. -01
8-PLACE DEC. -.005 SHARP EDGES A .03
VIEWS DISP.
DATE ISSUED
NAME:
DATE:
TITLE
9200-/+ 30 d-
MATERIAL:
MASTECH CONTRL DIVISION
LOWER SUPPORT
CYLINDER UNION
ORAWN A ADRIANSON
01/31/
6061-T6 ALUMINUM
DESTROY
PREVIOUS PRINTS
217C017
CHECK
REV DATE
CHANGE:
CHKD
FINISH
SCALE FULL
APPR
help_outline

Image Transcriptionclose

Geometric Dimensioning and Tolerancing 283 898 2 908 (000 893 386 898 2 Print supplied by MASCO Corporatio PR 13-1. Cylinder Union Lower Support. 800 6.61 O.010 -A- 3.31 1.25 DRILL THRU & C'BORE FOR 3/8-16 S.H.C.S. (FROM OPPOSITE SIDE) 4 PLACES DRILL & REAM THRU FOR 1/4 DIA DOWEL S.F. 4 PLACES .78 .014 M A .002 A B .25 L.. 2.921 2.342 96 2 3.34 1.585 4X 1.031 800 4.47 .171 ( 000 ) .454 .758 4X 1.5007/1.501 o .002 A 4X R.44 - 5/8-18 TAP 4 PLACES .562 THRU Ø.010 A B 0050 -B- 800 SECTION A-A 1 REQD. DO NOT SCALE ORAWING THIS DRAVING AND THE INFORMAYION CONTAINEDTHEREON ARE THE FROPERTY OTHERS AND MAY 8SED ONLY POR TE FURPOSE OF ENABL INO THE PARTY TO WHOM IT HAS BEEN LOANED TO QUOTE ON OR PILL AN OR0ER FOR MASCO UNLESS OTHERWISE SPECIFIED LAYOUT NAME ORAFT MASCO A CORPORATION ANGUL AR DIM- +/-.05 2-PLACE DEC. -01 8-PLACE DEC. -.005 SHARP EDGES A .03 VIEWS DISP. DATE ISSUED NAME: DATE: TITLE 9200-/+ 30 d- MATERIAL: MASTECH CONTRL DIVISION LOWER SUPPORT CYLINDER UNION ORAWN A ADRIANSON 01/31/ 6061-T6 ALUMINUM DESTROY PREVIOUS PRINTS 217C017 CHECK REV DATE CHANGE: CHKD FINISH SCALE FULL APPR

fullscreen
check_circle

Expert Answer

Step 1

The print sheet is showing the 3D view or perspective of the lower support cylinder union part.

Step 2

 

Answer to question no. 4

The boxes around the coordinate dimensions shows that the dimensions have no tolerance and the exact values have to be considered. Therefore, these dimensions are mentioned up to the exact coordinate locations having decimal point to the three digits.

Step 3

Answer to question no. 5

Both the views of the part indicates the presence of the permissible bonus tolerances. The identification is done by checking for letter M inside a circle mentioned in a feature control frame. Observe the image, t...

help_outline

Image Transcriptionclose

.562 THRU .008 M A

fullscreen

Want to see the full answer?

See Solution

Check out a sample Q&A here.

Want to see this answer and more?

Solutions are written by subject experts who are available 24/7. Questions are typically answered within 1 hour.*

See Solution
*Response times may vary by subject and question.
Tagged in

Engineering

Mechanical Engineering

Related Mechanical Engineering Q&A

Find answers to questions asked by student like you
Show more Q&A
add
question_answer

Q: 443. Heat Loss from a Buried Pipe A water pipe whose wall temperature is 300 K has a diameter of 150...

A: Given:

question_answer

Q: QUESTION 3 A high-pressure axial compressor for a stagnation pressure ratio of 8.5. The mass flow ra...

A: Write the expression for stagnation pressure ratio. 

question_answer

Q: Steam enters a turbine operating at a steady state at a pressure of 4 MPa, at temperature of 400 deg...

A: Write the energy balance equation for the steady flow turbine as given as follows:

question_answer

Q: Propane is contained in a closed, rigid container with a volume of 10 m^3.  Initially the pressure a...

A: Given:

question_answer

Q: The circuit breaker at a power seat motor continuously trips: Technician A says that this could be c...

A: The reasons for which a circuit breaker trips are as follows:Excess current flow due to overloaded c...

question_answer

Q: 7.29 A gearbox operating at steady state receives 4 hp along the input shaft and delivers 3 hp along...

A: (a)Write the expression for exergy balance.

question_answer

Q: The shaft of the wheel unit rolls without slipping and ao 8 ft/sec2 to the left, respectively, deter...

A: Given:

question_answer

Q: A table has a vertical sinusoidal motion with a ​constant frequency. What is the largest amplitude t...

A: A table has a vertical sinusoidal motion with a constant frequency. What is the largest amplitude th...

question_answer

Q: In the FILLET command, when selecting the objects to fillet, holding down the <Shift> key: a. ...

A: By holding the <Shift> key before selecting the second object when using a FILLET command, the...