Please explain on how to get the theta, Qin and Qout. It should betheta = 54.2461 degQ in = 0.0382 m3/sQ out = 0.0191 m3/smy professor said. but I don't have solution. used 9.807m/s² not 9.81.. thank you 1. A water jetpack suspends a 65kg man inair without motion along the vertical and thehorizontal as the man tilts the platform. Thejetpack has two outlets, each has a diameterof 5cm, and an inlet with a diameter of 6cm.Calculate the volumetric flowrate, in and outof the water jetpack, and the angle O suchthat there is no motion along any direction.Neglect the weight of the jetpack. The inlet isperpendicular to the outlet.inletWWQ i2Q0ВАCKSIDE

Given: The mass of the man is 65 kg. The water jetpack is shown below:

Please explain on how to get the theta, Qin and Qout. It should be theta = 54.2461 deg Q in = 0.0382 m3/s Q out = 0.0191 m3/s my professor said. but I don't have solution. used 9.807m/s² not 9.81.. thank you

Please explain on how to get the theta, Qin and Qout. It should be theta = 54.2461 deg Q in = 0.0382 m3/s Q out = 0.0191 m3/s my professor said. but I don't have solution. used 9.807m/s² not 9.81.. thank you

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 6. Draw the hydrograph and flow duration curve for the following data. Also find aven powerdevelo…

A: Given that, Week Discharge 1 100 2 200 3 300 4 1200 5 600 6 900 7 800 8 600 9…

Q: 4 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The ow direction is from 2 to 1 if AZ…

A: option d is correct

Q: A triangular gutter with side slope at angle 60 • has a depth 300 mm. Find the velocity of water, if…

Q: 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The flow direction is from 2 to 1 if AZ…

Q: EX IP the Howrate between two tanks is (a.s m/s), Ex: find CH)? KLE1.8 RL=1.3 Ls Soom LIE300 Di=300M…

Q: 33. An inward flow reaction turbine running at 450 rpm has an external diameter.of 50 cms and a…

Q: 3. Based from the pump performance curve below, calculate the following: a) Specific speed b)…

A: Given data Pump performance curve From the pump performance curve, specific speed and suction…

Q: xample 8.6: Find the depth and top width of a V-notch cap a maximum of 0.7 m³/sec and such that the…

Q: Determine the power required (Watts) to drive a reciprocating pump running at 1 rps and discharges…

Q: Q2/ Put a Circle around the correct Answer: 1/ Dimensions of discharge coefficient Cd are: a)…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: A turbine with a power coefficient Cp = 0.26 is able to generate 3.5 MW of electrical power with…

Q: The swept area of a wind turbine is 485 m´. The diameter of the rotor is Select one: a. 617.02 cm b.…

A: Given Data A=485 m2

Q: For the following figure, calculate the discharge (Q) of each pipe by using Hardy-Cross method…

A: here we have to calculate the discharge (Q) of the each pipe by using the hardy cross method

Q: A reciprocating pump running at 1 rps and discharges oil (p = 850 kg/m3) at a rate of 366.1 gpm. The…

A: GivenN=1rps=60rpmρ=850kg/m3Q=336.1 gpmd=250mm=0.250mL=500mm=0.5mH=39m

Q: A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are…

Q: Volume flow rate

A: Given; In a sand casting process,Sprue,D=10 mmHeight, hs=250 mmLeads to a runner which fills a…

Q: A pipe AB branches in to two pipes C and D as shown in fig. The pipe has diameters of 0.45m at A,…

A: We have given DA=0.45mDB=0.3mDC=0.2mDD=0.15mVA=2 m/sVC=4m/s

Q: QUESTION 5 5.1 A pipe of diameter 300 mm and length 3 000 m is used for the transmission of power by…

Q: 4) The nozte inlet Di =50mm otkt Dzo5mm う Dasred flow rete (9)-0.05m is P CPat) if P = 6 MP Hintd…

A: From Bernoulli

Q: Dynamic

A: ωAB=12 rad/svB=ABωAB=12*.2=2.4 m/sVB=vB→;VD=vD↑ Instantaneous center of bar BD lies at C…

Q: What is the velocity of the pipe center (m/s)? Given that h3=47.1 cm hy =7 cm h =3 cm Water

A: Solution:

Q: A pump delivers Q= 10.74 m3/s against a head of 15 m with a speed of 2000 rpm. Find the specific…

A: Given: Q=10.74 m3/s =10.74 x 15850.3= 170232.22 gal/min H = 15 m = 15 x 3.28084 = 49.2126 feet N =…

Q: Determine the TDH at 4500 m3/hr on the below pump curve using the minimum diameter. 1180 A.P.M. 140…

A: Given: To determine: TDH at 4500 m3/hr Efficiency NPSHR

Q: For the velocity profile shown find 1.The total displacement ,D(in): 2.The average speed,S(in/s):

Q: 300 mm 150 mm 2. 下 425 mm -Hg C13-6) heter venturi meter is installed in a 300mm diameter horizontal…

A: given diameter of venturimeter at point 1=D1=300mm=.3m diameter of venturimeter…

Q: Determine the power required (Watts) to drive a reciprocating pump running at 1 rps and discharges…

A: Given data: N=1 rpsρ=850 kg/m3Q=369.2 gpm=0.0233 m3/sd=250 mmL=500 mmH=28 m Need to determine the…

Q: A double acting hydraulic cylinder has a bore of 100 mm. The rod is 40 mm in diameter and the stroke…

A: Given, Cylinder bore = D = 100 mm Rod diameter = d = 40 mm Stroke = L = 120 mm Force = F = 12 kN…

Q: Q 1: Find the number of passes needed to pull the aluminum wire from a diameter of 4 to a diameter…

Q: A turbine develops 10 MW under a head of 25 m at 135 rpm. a) What is the specific speed? b) What…

A: Data given- P = 10 MW = 10 × 103 kW H = 25 m N = 135 rpm For b) & c) H2 = 20 m

Q: e marimum velocity of slidi

Q: 2. Given the figure below, solve for flow rate in the venturi meter. (C = 0.984) Ø= 400mm 2 (Ø =…

Q: Q3:- One of the companies wanted to drill an oil well in one of the fields in depth (6000 ft and…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: A fabricated assembly made from three different sizes of standard steel tubing is shown below. The…

Q: Q9- if the pump shown in figure develops 5hp on the flow what is ti (Q=0.0335m/sec)

A: given:P=5HP

Q: P1/ In the fig.shown, the Flow rate in Pipe (A) is equal (QA= 25 Lit15), the diameter is equal (…

Q: Let A= 1200 ft/min? and Vo = 85 in/s. Find s in inches at the end of 11.8 sec. Write your answer in…

A: Given Data A=1200 ft/min2 Vo=85 in/s t=11.8 s

Q: Figure shows the water flows through a pipe AB with a 1.2 m diameter at 3 m/s and then passes…

A: Basics of Pipe flow.

Q: Length and dia. Of pipe 1 are 2000m and 1m while the second pipe is 2000m and dia. Of 0.8m .Find the…

A: we are suppose to solve only one question. please post other question as separate question.

Q: Oil (s.g. = 0.84) flows through a 29-in-diameter pipeline at 7214 gpm. Compute the average velocity…

A: Given Diameter, d = 29 in = 0.736 m Flow rate, Q = 7214 gpm = 0.4551 m3/s

Q: A pump has a specific speed of 42 and 600 rpm when it delivers 0.01 m3/s. find the head developed by…

Q: 10.86 An air-conditioning system is designed to have a duct with a rectangular cross section 1 ft by…

A: Given Data For the same pressure drop along the pipe ∆hrect=∆htrap (hf)rect=(hf)trap Hydraulic…

Q: Draw and explain the working principles of the following flow measurement devices (Copying from the…

Q: Th4 Base is Snmly moved wilh The Veloci ky of 5 m/s Find The Velociy and Acceloratronof Head

A: Let the width be x ft length = (3x−70) ft Perimeter = 940 ft Also Perimeter of rectangle = 2(l+w)…

Q: A hydraulic vane pump running at 1800 rpm develops 2 L/s flow at 750 kPa. Volumetric efficiency is…

Q: Need asap A horizontal pipe of cross section 1.5 in2 has a constriction of cross section of 2 cm2 .…

A: Given data, Horizontal pipe area a1=1.5 in2 Or a1= (1.5/144) ft2 Constriction area a2 = 2 cm2 Or…

Q: Let A= 1200 ft/min? and Vo = 85 in/s. Find V in inches per second at the end of 12 sec.

Q: A turbine is rated at 1512099 btu/hr when the flow of the water through it is 0.67 m^3/s. Assuming…

A: Find the head in meter acting on the turbine.

Q: A three stage pump delivers 1.89 m3/s against a head of 200 m with a speed of 2000 rpm. Find the…

Q: 7.8 A turboblower develops 750 mm W.G. at a speed of 1480 rpm and a flow rate of 38 m³/s. It is…

A: (a) The specific speed of the model is 1.42 (b) The flow rate through the model is 9.63 m3/s

Q: EX (3) Find the flow rate (Q1, Q2, Q3), if Qt -20 m3/sec, v- 1.12 10 m2/s. Pipel L (m) D(mm) 100 E…

Question

100%

Please explain on how to get the theta, Qin and Qout. It should be

theta = 54.2461 deg

Q in = 0.0382 m3/s

Q out = 0.0191 m3/s

my professor said. but I don't have solution.

used 9.807m/s² not 9.81.. thank you

1. A water jetpack suspends a 65kg man in
air without motion along the vertical and the
horizontal as the man tilts the platform. The
jetpack has two outlets, each has a diameter
of 5cm, and an inlet with a diameter of 6cm.
Calculate the volumetric flowrate, in and out
of the water jetpack, and the angle O such
that there is no motion along any direction.
Neglect the weight of the jetpack. The inlet is
perpendicular to the outlet.
inlet
W
W
Q i
2Q0
ВАCK
SIDE

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

The water jet in figure, moving at 15 m/s, is split so that one-third of the water moves towardA. Calculate the magnitude and direction of the force on the stationary splitter.
A cylindrical tank discharges water at 20^O C through a well-rounded orifice to hit an inclined plate as shown in the figure. Determine the components of the force exerted by the fluid jet on the plate inclined at 60^O from the horizontal.( Assume the external and internal pressures are the same)
A fire hose discharges water through a nozzle having a diameter of 2.5cm. The head lost in the nozzle is 4% of the velocity head in the jet. If the gage pressure at the base of the nozle is 400kpa, find the flow and the maximum horizontal range to which the stream can be thrown.
A jet of water strikes a stationary curved vane and is deflected by 150° from its originaldirection. The mass flow rate from the jet is 0.68 kg/s and has a velocity of 24 m/s. Calculatethe magnitude and direction of the resultant force on the vane.
A water pump has an outlet diameter of 70 mm horizontal pipe flowing full at the outlet. The resulting jet strikes the ground surface at a horizontal distance of 32 m and a vertical distance of 1.75 m from the outlet. Find the pumping capacity in liters per minute.
A jet of water 50mm in diameter with a velocity of 18 m/s strikes a flat plate inclined atan angle of 25° to the axis of the jet. Determine the resultant force exerted on theplate.
A tank has one of its side inclined inward at an angle of 30 degrees with horizontal. The free surface of the contained water is at Elev 15.25 m. The orifice located on the inclined side issues a jet, having its vena contracta at Elev 10.70 m. If the highest point in the trajectory of the jet is at Elev. 14.00m, find the actual velocity of the jet. Neglect air friction. Include Illustration if needed. a.9.3 m/s b.8.3 m/s c.10.3 m/s d.11.3 m/s
A jet of water 4cm diameter enters a fixed curved vane with a velocity of 50 metres/sec at an angle 20 degree to the horizontal. Find the normal and tangential forces exerted by the jet, if it leaves the vane at angle 15 degree to the horizontal
Please use the momentum theorem to solve this problem
Find the force exerted by a jet of water of diameter 75 mm on a stationary flat plate, when the jet strikes the plate normally with velocity of 20 m/s.
| The cross-sectional area is 25 square centimeter of water jet under the velocity of 35 meter per second and strikes tangentially a curved plate. The curvature angle of plate at the outlet is 120° with the x-axis. Find the force exerted by the get on the plate in the direction motion. Solve the problem, when the case of the plate is stationary and plate is moving in the direction of jet with the velocity of 15 meter per second.
A water jet of diameter 3 cm is striking on a inclined. The velocity of the water is 56 m/s. Calculate the force exerted on the plate if the inclination is 50°.