3.(If relevant) A clearly labeled diagram (or diagrams) clearly pertaining to your analysis with a coordinate system and relevant labels.Final answer with appropriate units and significant figures. You can use the fprintf() command in MATLAB to format numerical resultsA 2-3 sentence reflection on your answer. Does it make sense? Why or why not? What are some implications? Cantilevered rod OA is 0.5 m long, and made from AISI 1010 hot-rolled steel. A constant force and torque are applied as shown. Determinethe minimum diameter, d, for the rod that will achieve a minimum static factor of safety of 2(a) using the maximum-shear-stress failure theory.(b) using the distortion-energy failure theory.150 NA25 N-m

Cantilevered rod OA is 0.5 m long, and made from AISI 1010 hot-rolled steel. A constant force and torque are applied as shown. Determine the minimum diameter, d, for the rod that will achieve a minimum static factor of safety of 2 (a) using the maximum-shear-stress failure theory. (b) using the distortion-energy failure theory. 150 N 25 N-m

Cantilevered rod OA is 0.5 m long, and made from AISI 1010 hot-rolled steel. A constant force and torque are applied as shown. Determine the minimum diameter, d, for the rod that will achieve a minimum static factor of safety of 2 (a) using the maximum-shear-stress failure theory. (b) using the distortion-energy failure theory. 150 N 25 N-m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.4.8P: Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the...

See similar textbooks

Similar questions

answer this ; The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion)
An aluminum alloy is to be used for a solid drive shaft such that it transmits 30 hp at 1200 rev>min. Using a factor of safety of 2.5 with respect to yielding, determine the smallest-diameter shaft that can be selected based on the maximum shear stress theory. sY = 10 ksi.
The figure (attached) shows a belt pulley mechanism which is loaded statically. The shaft is made of AISI 1030 steel with the yield strength of 480 MPa. Using distortion energy theory (DET), determine the diameter of the shaft with a factor of safety of 2.
A shaft is loaded in bending and torsion such that Ma = 69 N · m, Ta = 42 N · m, Mm = 52 N · m, and Tm = 31 N · m. For the shaft, Su = 700 MPa and Sy = 560 MPa, and a fully corrected endurance limit of Se = 210 MPa is assumed. Let Kf = 2.2 and Kfs = 1.8. With a diameter of 28 mm, determine the yielding factor of safety using von Mises stress to consider the possibility of static failure in the first load cycle.
A bar AISI 1035 steel forged and heat treated with minimum yield strength of 570MPa is subjected to bending moment of 290Nm and a torsional moment of 310Nm. Assuming a factor of safety of 2, determine the diameter of rod using the following theories of failure (i) Maximum Shear stress theory and (ii) Distortion Energy theory (iii) Maximum stress theory, also specify which diameter is considered as safe
A solid circular shaft has a diameter of d mm and is made from steel, which fail when tested in simple tension test at a stress of 150 MPa. The shaft was subjected by bending moment and torque which are 22.2 kNm and 44.4 kNm respectively. Calculate the minimum allowable shaft diameter, d according to:- (a) Tresca failure criterion (b) Von Mises theory of elastic failure
The components of plane stress at a critical point on a thin steel shell are shown. Determine if failure (yielding) has occurred on the basis of the maximum distortion energy theory. The yield stress for the steel is sY = 700 MPa.
The material of a certain transmission shaft uses AISI 1030 HR, its yield strength is 260 MPa, the transmission torque of this shaft is 160 N·m, and it is subjected to a uniform axial tension of 0.5 kN. Please calculate according to the Distortion energy theory. The minimum shaft diameter with a safety factor n of 2.5 (to 2 decimal places).
a helical compression spring with squared and ground ends is made of shot-peened astm a232 spring wire with presetting(G=79 GPa) . It is used to control a cyclic dynamic load that varies between 562 and 0 N. if a saftey factor of 1.12 is used, determine the allowable shear stress for a design cinsideration of infinite fatigue life
A cylinder which can be considered as a thin-walled shell, is made of steel plate 16 mm thick and is 2.14 m internal diameter. The cylinder is subjected to an internal fluid pressure of 0.55 MN/m2 gauge and, at the same time rotated about its longitudinal axis at 3000 rev/min. Determine:(a) the hoop stress induced in the wall of the cylinder due to rotation:(b) the hoop stress induced in the wall of the cylinder due to the internal pressure:(c) the factor of safety based on an ultimate stress of the material in simple tension of 456 MN/m2. Steel has a density of 7.8 Mg/m3.
A load P is supported by two springs arranged in series. The upper spring has 20 turns of 19 mm diameter wire on a mean diameter of 150 mm. The lower spring consists of 15 turns of 12 mm diameter wire on a mead diameter of 125 mm. Determine the spring index of the lower spring in MPa if the total deformation is 76 mm and G of 83 GPa.
Torque in = 40nm Holding torque out = 896nm 8.Using your answers from the gear box above, and given that the input shaft has a diameter of 12 mm and the output shaft has a diameter of 15 mm, both shafts are made from aluminium. When this transmission system was operated, it failed. Identify the position where the failure occurred and the reason for this failure. Suggests improvements to the system to overcome the failure mode. The shear strength of aluminium is 207 MPa.