Prob 2. The cantilever beam shown in the figure is built into a wall 2 ft thick so that it rests against points A and B. The beam is 10 ft long and weighs 150(2+x) lb per ft. Determine the reactions at A and B. Let x be the last number of your student # , e.g., 2nnn-nnnnn5, x=5. Use PMDAS to calculate the given load. If you calculate the incorrect load, then you'll get no points for this number. X=6 4 ft 4000 lb 4 ft 150(2+x) lb/ft A 2 ft B

Prob 2. The cantilever beam shown in the figure is built into a wall 2 ft thick so that it rests against points A and B. The beam is 10 ft long and weighs 150(2+x) lb per ft. Determine the reactions at A and B. Let x be the last number of your student # , e.g., 2nnn-nnnnn5, x=5. Use PMDAS to calculate the given load. If you calculate the incorrect load, then you'll get no points for this number. X=6 4 ft 4000 lb 4 ft 150(2+x) lb/ft A 2 ft B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the beam given in the figure. Given E=29000 ksi and I=100 in4 . Compute the the reactions for the given beam if support B settles by 1.8 in.
Learning Goal: To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=2.0a=2.0 ftft, b=6.0b=6.0 ftft, and c=11.0c=11.0 ftft. The applied forces are F1=1.50F1=1.50 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=35∘θ=35∘ with the horizontal. Neglect the weight of the beam. Determine the vertical reaction at A. Determine the horizontal component of the pin reaction at C. Determine the vertical component of the pin reaction at C.
To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=4.5a=4.5 ftft, b=6.5b=6.5 ftft, and c=10.0c=10.0 ftft. The applied forces are F1=1.40F1=1.40 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=60∘θ=60∘ with the horizontal. Neglect the weight of the beam.(Figure 1) 1. Determine the vertical reaction at A. 2. Determine the horizontal component of the pin reaction at C. 3. Determine the vertical component of the pin reaction at C.
Thumbs up will be given. Please write the complete solutions in 4 decimal places legibly. Solve manually and draw the FBD. Box the final answer. Calculate the reaction components at the points of support of the beam shown using the Double Integration Method and Area Moment Method Let P = 147
AS SHOWN IN THE FIGURE, A RIGID BEAM WITH NEGLIGIBLE MASS IS PINNED AT ‘O’ AND SUPPORTED BY TWO RODS IDENTICAL EXCEPT FOR LENGTH. A = 100 mm2 & E = 200 GPa. DETERMINE THE LOAD IN EACH ROD IF P = P3.
Calculate for the axial force in kN at member BA of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the module of F should be greater than 369.18N, so that it would still remain balanced in that position?
Solve the given beam, figure 7, to draw bending moment diagram by parts at a section B and then calculate the moment of area of the M diagrams about B. (i.e. calculate AreaBC * xB ). The reaction forces are R1=83.33 N, R2=366.67 N.Figure
There is a door-shaped structure bearing force as shown in the figure below. The E of the entire section is 30000 kips/inch^2, and the I is 300^in4. Try to analyze this structure, calculate the end point bending moment of each member.
Calculate the bending moment at B. Let W = 14 kN/m Indicate the Minus sign (-) if answer is negative. For positive answer "no need" to write the (+) sign.
Calculate the equivalent force of the distributed load and the Support Reactions (Ax, Ay and By).
Find the maximum moment of the given load train at point n on the beam given in the figure?(Single load and distributed load train move on the beam. (a=9 m between n-A, b=3 m between n-B)