Problem 01. The pin-jointed frame in the figure below has members of cross-sectional area A=1200mm² and young modulus of elasticity of 200.5 GPa. If a vertical concentrated load of 1200KN (downward) and horizontal force of 800KN (to the right) are applied at Point D. Determine: a. The vertical displacement at D in mm. b. The horizontal displacement at D in mm. c. The stress of AD due to actual loads in kN. d. The stress of AB due to horizontal unit load. e. The stress of BD due to vertical unit load. 4m B 3m 3m F E

Problem 01. The pin-jointed frame in the figure below has members of cross-sectional area A=1200mm² and young modulus of elasticity of 200.5 GPa. If a vertical concentrated load of 1200KN (downward) and horizontal force of 800KN (to the right) are applied at Point D. Determine: a. The vertical displacement at D in mm. b. The horizontal displacement at D in mm. c. The stress of AD due to actual loads in kN. d. The stress of AB due to horizontal unit load. e. The stress of BD due to vertical unit load. 4m B 3m 3m F E

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

Two uniform loads of 112 kN/m acting downward are supported by a uniform upward pressure of q as shown in the figure.
Since the beam M in the figure is under the effect of simple bending moment, calculate the bending stress and shear stress values at the A, B and C points. h = 400mm b = 140mm and M = 150KNm
T (Shear force) and M (Bending) for the system whose loading condition is given in Figure 1.Draw the moment diagrams. Calculate the deflection (vertical displacement) at point B in mm using Castigliano's Theorem. The beam bending stiffness (EI) is constant along the bar and its value is 50 000 kNm2. q=1,4(kN/m) a=8(m) El=50000(kNm2)
The T-shaped beam shown above is supporting a concentrated load P at its free end. The beam has an allowable bending stress of ?????? = 250 MPa and an allowable shear stress of ?????? = 100 MPa. a) Determine the distance to the neutral axis (?̅), second moment of area (?), and the section modulus (?) of the cross-section.b) Draw the shear force diagram (SFD) and bending moment diagram (BMD) of the beam. On your diagrams, express the values of shear and moment in terms of the applied load P.c) Determine the maximum value of P such that bending failure will not occur.d) Determine the maximum value of P such that shear failure will not occur.e) Based on your answers to (c) and (d), what is the maximum load P that can be applied to the beam? Is this beam bending or shear governed?
Consider a 180-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 60 kN-m and 68 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 120 mm, b2 = 30 mm, b3 = 200 mm, d1 = 65 mm, d2 = 175 mm, d3 = 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Consider a 155-mm-long segment of a simply supported beam. The internal bending moments on the left and right sides of the segment are 75 kN-m and 79 kN-m, respectively. The cross-sectional dimensions of the flanged shape are shown in the accompanying figure. Assume b1 = 135 mm, b2= 50 mm, b3= 205 mm, d1= 65 mm, d2= 180 mm, dz= 65 mm. Determine the maximum horizontal shear stress in this segment of the beam.
Determine the vertical displacement at Joint A, B, C, D, E
Given the figure below. Use UNIT LOAD METHOD in determining the maximum deflection at midspan. E and I are constant. 1. What is the reaction at A of the real beam? 2. In constructing the virtual beam and determining the maximum deflection, where must be the 1-unit load be placed? 3. What is the reaction at the support of the virtual beam? 4. In solving the maximum deflection at midspan, how many portions or segments must the beam be divided so that the real and virtual loadings are continuous in each segment? 5. Consider segment AB of the real beam, with x measured from A, what is the moment equation M_(AB ) ? 6. In question 4, what are the limiting values of x? 7. Consider segment AB of the virtual beam, with x measured from A, what is the moment equation? 8. Analyzing segment BC of the real beam, with x measured from A, what is the moment equation M_BC? 9. In the given beam, if the 50 KN load is moved 2m closer to A and deflection at midspan is desired, how many segments must the…
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
if the beam is subjected to a bending moment of m = 10 kN•m, determine the bending stress in the beam at points a and b, and sketch the results on a differential element at each of these points.
The internal shear force V at a certain section of a steel beam is 80 kN, and the moment of inertia is 64,867,500 mm4. Determine the horizontal shear stress at point H, which is located L = 17 mm below the centroid. 58.9 MPa 42.7 MPa 39.6 MPa 35.2 MPa 31.2 MPa