!Required informationProblem 01.061 - A two link assembly with point loadsTwo horizontal 13-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at eachconnection.0.3 in0.5 in18 inProblem 01.061.c - Bearing stress in a linkDetermine the average bearing stress at Bin member BCThe average bearing stress at Bin member BC is 24.65 ksi.

Answered: Image /qna-images/answer/e9999257-8fe5-4977-b411-7697796e5f96.jpg

Answered: Problem 01.061- A two link assembly…

Problem 01.061- A two link assembly with point loads Two horizontal 13-kip forces (P) are applied to pin 8 of the assembly shown. A 0.8-in. diameter pin is used at each connection. 03 m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.15P: An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at...

See similar textbooks

Related questions

Q: Adiabatic steam turbine has inlet of 6 kg/s at 5 MPa, 600 oC. The actual steam exit from turbine is…

A: Given:Mass flow rate of steam, m=6 kg/sInitial pressure of steam, P1=5 MPaInitial temperature of…

Q: The beam is to be hoisted using two chains. Determine the magnitude of force FA in order to develop…

Q: 1. The force convection coefficient for a hot fluid flowing over a cool surface is 120W/m2-K. The…

A: For solution refer below images.

Q: A train travels along a circular track having a radiusof 2000 ft. If the speed of the train is…

A: Given:- A train travelling along a circular track Radius of track (R) = 2000 ft Initial velocity…

Q: A specimen of copper having a rectangular cross section 15.2 mm × 19.1 mm (0.60 in. X 0.75 in.) is…

A: Given:Area of cross-section of specimen, A=15.2 mm x 19.1 mmForce applied on the specimen, F=44500 N

Q: Compute the moment (positive if counterclockwise, negative if clockwise) of the 0.39-lb force about…

A: Given data: F=0.39 lb Need to determine the moment about the point O.

Q: Find a formula to obtain the relative humidity of the air at different altitudes or atmospheric…

Q: An experimental device imparts a force of magnitude F = 32 lb to the front edge of the rim at A to…

Q: A mass, spring and a damper system is subjected to an external harmonic excitation of 200cos15t (N).…

A: Write the expression of mass, spring and damper system. md2xdt2+cdxdt+kx=Fext

Q: The 43-kg cylinder is suspended from a clamping collar at C which can be positioned at any…

A: (a) Draw the free-body diagram of point C. Write the angles α and β.…

Q: A frictionless weighted piston in a cylinder contains 1 kg of wet steam at 100 °C and has a volume…

A: Part 1: Mass of steam inside the cylinder = 1 kg T1 = 100 oC V1 = total volume = 0.1 m3 It is…

Q: I Enumerations: Main classifications of engineering materials. 5-8. Components of the discipline of…

A: (a) Engineering materials can be classified mainly into metallic and non metallic. In metallic,…

Q: 1. The sum of the sphere volumes of all atoms within a unit cell (assuming the atomic hard sphere…

A: Dear student, According to the guidelines, I am allowed to answer only three…

Q: A new foam-like material called Aerogel is the lightest, most porous solid material ever made. The…

A: Given: Specific gravity of Aerogel = S = 0.00325 Volume pick-up by one truck = V = 48 ft3 = 1.3592…

Q: What prerequisites must be satisfied in order to produce a user-defined identification?

A: given; prerequisites ,it can be specified as package specification within SQL statement.

Q: 4. The pump of a water distribution system is powered by a 15-kW electric motor whose efficiency is…

A: Given data: Pmotor=15 kWηmotor=90%Q=50 L/s=50×10-3 m3/sPi=100 kPaPo=290 kPa Need to determine the…

Q: B- A6-mm-diameter electrical transmission line carries an electric current of 50 A and has a…

A: Given Diameter, d = 6 mm Current, I = 50 A Velocity, v = 40 km/h = 11.11 m/s Find Surface…

Q: When the load L is 6.8 m from point C, the tension T in the cable has a magnitude of 8.6 kN. Express…

Q: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as…

Q: If the inner diameter of the penstock that deliver water form the dam to the hydroelectricpower…

Q: Determine the Magnitude,direction and sense of the resultant for the Coplanar concurrent force…

Q: A weight W 75 kN is applied eccentrically from the end of a cantilevered circular pipe of length L =…

Q: The thermodynamic process of a substance when it passes through device changes in a constant…

Q: An experimental device imparts a force of magnitude F = 32 lb to the front edge of the rim at A to…

A: Moment calculation has given in 2 methods.

Q: 5. A student living in a 4 m x 6 m x 6 m dormitory room turns on her 150 watts fan before she leaves…

A: The given data in the problem is represented in the following attached image:

Q: Each propeller of the twin-screw ship develops a full-speed thrust of F = 245 kN. In maneuvering the…

Q: பாடு my mgu immunalme mun F₁ 1800 N கும E B E Ammy quy Kuyார்யQue N IN um@mmmmmmmm யோகியAmmmm…

A: Given, let's write the forces in vector form, and use dot product to find the angle between them

Q: Problem Solving: Solve the problem with complete solution in landscape orientation by placing it in…

A: To find external reaction at D and stress in member BC,DE

Q: Q3/ For the figure below: a) The total area is: 2 6"

A: Given: To determine the total area and the centroid of the given composite figure.

Q: A rigid 0.15 m³ tank contains air at 0.8 MPa, 200°C. A valve on the tank is now opened an flows out…

A: Find final mass of air in the tank. Find exit enthalpy of air .

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

Q: Acentrifugal pump is pumping oil with ?= 860 kg/m3at a rate of 0.1 m3/s.The inlet and outlet…

A: Find Power input to the pump.

Q: 1. Consider a four bar linkage with the following links: L₁ = 180mm, L₁ = 40mm, L₂=170 mm. Using…

Q: For real diffusers the exit velocity can be practically equal to zero. O True O False

A: Answer : FALSE DIFFUSER: It is a device which slows down the fluid motion . In this device velocity…

Q: while assigning properties to the boiler it is not necessary to enter value in number of increment…

A: In essence, a boiler or steam generator is a space from which water may be forced and steam can…

Q: briefly discuss ways of protecting a mental from corrosion

Q: An experimental device imparts a force of magnitude F = 36 lb to the front edge of the rim at A to…

Q: The 400-kg precast concrete section is hoisted by a vertical force 'T' from a crane. Find the…

A: Calculate the vectors AB, AC and AD.…

Q: Problem 5 (a) A 10-mm-diameter Brinell hardness in- denter produced an indentation 2.50 mm in di-…

Q: A 0.025-mm-diameter stainless steel wire having k=16 W/m C is connected to two electrodes. The…

Q: In thehydroelectric power plant, water enters the turbine nozzles at 700 kPa absolute witha low…

Q: 4) Figure shows a gas contained in a vertical piston-cylinder assembly. The total mass of the piston…

A: Given data: m=100 kg∆U=0.1 kJ∆PE=0.2 kJPatm=1 barg=10 m/s2A=0.01 m2 Need to determine the work done…

Q: 1-50. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps…

Q: 2. The center diagonal of the truss in the figure shown can support tension only. Compute the force…

A: For the given truss To determine the force of DG and BE

Q: HEAT CONDUCTION ON PLANE WALLS 11. A composite wall is formed of a 2.5-cm bronze plate (k = 26…

A: Given: Length of bronze plate→L1=2.5 Cm=0.025 m Conductivity of the bronze plate→k1=26 W/m°C Length…

Q: 1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C.…

Q: A centrifugal pump is pumping oil with p = 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet…

Q: 2. Given that the resultant force is zero and its resultant moment is 150 lb ft counterclockwise,…

A: GivenR=0M=150lbft

Q: 1500 A 3600 B + M 1800 С 2400

A: Given, first let's find out which force F_AB and F_BC is greater.

Q: A solar radiant heat flux of 700 W/m2 is absorbed in a metal plate that is perfectly insulated on…

A: Given : solar radiant heat flux, q' = 700 w/m2 convection heat transfer coefficient , h = 11 w/m2.…

Question

!
Required information
Problem 01.061 - A two link assembly with point loads
Two horizontal 13-kip forces (P) are applied to pin B of the assembly shown. A 0.8-in. diameter pin is used at each
connection.
0.3 in
0.5 in
18 in
Problem 01.061.c - Bearing stress in a link
Determine the average bearing stress at Bin member BC
The average bearing stress at Bin member BC is 24.65 ksi.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. A 2 kip/ft distributed load is applied on member AB, which is supported by a pin at A and bar BC. The connections at points A and B are shown in detail. All pins have a diameter of 0.5 in while all members have cross-sectional dimensions of 1.5 x 1 in. Determine the following:a. maximum normal stress in member BC (ksi)b. normal and shear stress in a horizontal section across member BC apart from the pin (ksi)c. shear stress in pins A and B (ksi)d. maximum bearing stress on member AB (ksi)
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 14 × 1214⁢ × 12 -in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 3838 -in.-diameter pins, while member BCD is connected to its support at B by a 516516 -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.05 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. The largest load P that can be applied at D is lb.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips.Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 4 kips, R = 18 kips and S = 21 kips. Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A.Answer: F1 = ? kips.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 115 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 3 mm, and an allowable normal stress of 65 MPa. Assume x3 = 3.7 m, x2 = 1.5 m, and y; = 4.1 m, Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress
circular cross-section belt pulley system supported by two bearings tensioning forces formed in belts in Shaft power transmission T11 = 8 kN, T12 = 2 kN, T21 = 8 kN and T22 = 2 kN. Pulley weights are 1 no.lu pulley for both pulleys W =6 kN. Each two pulley diameters d = 1,2 m dir. a = 0.2 m ve b = c = 0,4 m. Slip safety stress Jul = 70 MPa a-) Greatest shear stress (TRESCA) b-) The diameter of the shaft (d) according to the largest change in shape (VON MISES) criteriayou can find.
Topic: MACHINE DESIGN A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull whenthe vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3
Design the spigot (in tension and compression) of the spigot and socket cotterjoint which is subjected to alternate tensile and compressive loading of 50 kN usingthe following data:Yield strength of cotter material SYS = 400 N/mm2, Factor of safety = 4 (for spigot)Assume thickness of cotter, t = 0.30d, where d is the diameter of the rod.
A load P is supported by two concentric steel springs.Given:Inner Spring:30 turns of 20-mm ø wireMean ø = 150 mmOuter Spring:20 turns of 30-mm ø wireMean ø = 200 mmFind the maximum load that will not exceed a shearing stress of 140 MPa in eitherspring. G = 83 GPa.
A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the flange thickness if the bearing stress on the flange is 95 MPa. A. 10 mm B. 20 mm C. 25 mm D. 30 mm
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution