Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution

Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
A composite shaft is made by slipping a bronze tube of 3-in. outer diameteran -in. inner diameter over a solid steel shaft of the same length and 2-in.-diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 8 ksi for bronze and 12 ksi for the steel? For bronze, G = 6 x 106 psi, and for steel, G = 12 x 106 psi
1. A steel shaft is to be manufactured either as a solid circular or as circular tube. The shaft is required to transmit a torque of 1200 Nm without exceeding an allowable shear stress of 40 MPa, nor an allowable rate of twist of 0.75º/m. For G = 78GPa, determine: a. The required diameter do of the solid shaft.b. The required outer diameter d2 of the hollow shaft if the thickness t of the shaft is specified as one-tenth of the outer diameter.c. The ratio of diameters (that is, the ratio d2/do and the ratio of the weights of the hollow and solid shafts.
A solid shaft in a rolling mill transmits 20 kW at 2 revolutions per second. The length of the shaft is 3 m and modulus of rigidity is 83,000 MPa. Which of the following gives the torque carried by the shaft?a. 1.59 kN-m c. 2.69 kN-mb. 3.45 kN-m d. 4.81 kN-m Which of the following gives the minimum diameter so that the allowable torsional shearing of 40 MPa will not beexceeded?a. 88 mm c. 59 mmb. 45 mm d. 76 mm Which of the following gives the minimum diameter so that the allowable angle of twist of 6O will not be exceeded?a. 29 mm c. 35 mmb. 49 mm d. 55 mm
Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outer diameter and 80mm inner diameter. The shear stress is limited to 70 MPa, and the angle of twist must not exceed 0.4 degrees in a length of one meter. Use G = 83 GPa for steel.