Answered: PROBLEM 1 Find the moment of inertia of…

Engineering

Civil Engineering

PROBLEM 1 Find the moment of inertia of the section with respect to x-axis (lx). Y 1m- 1 m 4 m -3 m- x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For a runway at an elevation of 1000 m above MSL and airport reference temperature of 16 °C, the…

A: Given, Airport reference temperature, ART = 16 oC Runway elevation = 1000 m above MSL Standard…

Q: An steel shaft consists of a hollow shaft 3m long, with an outside diameter of 200mm and an inside…

Q: Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN…

A: Given data in question Loads Area Elasticity modulus Length Statically indeterminate To find out…

Q: A camera equipped with a 152 mm focal length lens is used to take a vertical photograph from a…

A: Given data- focal length f==152 mmFlying height H=2789 melevation h=500 mTo Find-The scale of the…

Q: 2-An open tank 6 m long, 2.4 m deep and 3.6 m wide contains oil of specific gravity 0.85 to a depth…

Q: On a certain bus terminal, there are two terminals that can travels to the south. The number of…

A: Part 2 Average waiting time in the queue =100/150= 0.665 Hence option B is correct Part 1…

Q: 1/49 scale model dam was used to simulate the in-situ flow conditions. Assuming that the model…

Q: Use the Conjugate beam method to determine the slope at A and displacement at C. EI is constant. 5…

Q: 3.11 Each of the following statements describes a silicate mineral or mineral group. In each case,…

A: Given the following statements are describing a silicate mineral or mineral group. Since we only…

Q: answers may be positive or negative. Here, "maximum" d enter your shear force and bending moment…

Q: Z C310 x 45

Q: the flow rate

A: Continuity equation: -For one dimensional flow of steady fluid mass flow rate is constant.

Q: An unsupported excavation is made to the maximum possible depth in a clay soil having Y₁ = 18 kN/m³,…

Q: Determine the horizontal component of the wind force tributary to the roof diaphragm. The basic wind…

Q: determine the normal force (in Newtons). Use g = 9.81 m/s².

Q: Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P₂2 = 88 kN…

A: From figure ; Considering Equilibrium : PCD = RD PBC = RD - P2 PAB = RD - P1 - P2

Q: 50 ton freight car is drawn 2500 ft up along a 1.2% grade at constant speed. Find the work done…

Q: In a rectangular channel 3.5 m wide laid at a slope of 0.0036, uniform flow occurs at a depth of 2…

Q: is tied to a

A: Le the volume of lead = VWe knowfor submerged and equilibriumBuoyancy force = weight of the…

Q: 100 lb/in. A -30 in.- 40 lb/in. B 1.8 in. O

Q: ACTIVITY 3- Beam Analysis Analyze the loaded beam as shown. Be guided as follows: a. Solve for the…

A: Load and beam diagram is given as shown in the figure above and it has been asked in the question to…

Q: In the figure shown, find the y-coordinate or the distance y of point A so that the 400 N force will…

A: Given .force =400N

Q: Situation 6: A steel plate is 280 mm wide and 15 mm thick with 4 bolts (24mm dia.) cut into the…

A: Net area The net area of a member is the gross sectional area minus the holes or notches. Punching…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: Given A cantilever beam Required Shear force and bending moment diagram using area method. And…

Q: WWW

Q: A fully saturated clay sample has a mass of 1526 grams. After oven-drying, its mas was reduced to…

A: Wt of fully saturated sample = 1526 g Wt of dry sample= 1053 g Wt of water = 1526-1053= 473 g Water…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: The soil borrow material to be used to construct a highway embankment has a wet unit weight of 15.4…

Q: Compute for the density of the liquid in kg/m^3.

A: This question is from Fluid mechanics

Q: From the list below, select the assumptions needed for a neutral axis to pass through the centroid…

A: The neutral axis always passes through the centroid of the cross sectional area and is found out by…

Q: A Santol plantation has statistical records showing that if 25 santol trees are planted, each trees…

A: Each santol tree yield=500 No. of trees=25 For each extra tree avg. production of Santols decreases.

Q: Q.4: If the gas oil ratio = 560 Scf/STB at initial pressure of 4300 psia, calculate the GOR at…

A: Given, GOR at initial pressure = 560 scf/stb Bubble point pressure = 3500 psi

Q: 10.1 A simply supported steel column is 8 ft long and has a square cross section of side length b.…

A: using eulers equationPcr=π2EIL2Pcr=π2Eb412L2b4=12PcrL2π2E

Q: 16-10. Determine the internal loadings at the ends of each member. Assume and 3 are pins. Take E =…

A: Given data:- The modulus of elasticity, E=200 GPa The moment of inertia,I=250×106 mm4 A=6.45×103 mm2

Q: Problem 02 Determine the LRFD design strength and the ASD allowable strength for each of the…

Q: a) plot how the critical stress intensity kc depends on the thickness and explain this?

A: Critical stress intensity:- The factor of critical stress intensity is used for finding the fracture…

Q: Consider R=A+B+D, which of the following is correct? O sine=Ry/Rx OR = √(R₂)² + (R₂)² O tane=Ry/Rx O…

A: Given data: R⇀=A⇀+B⇀+C⇀

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 470 Ib-ft, Te = 1090 lb…

Q: Determine the flexural stress and shear stress of the beam loaded as shown in the figure

A: Let's find out the support reactions first For the equilibrium of the static of the beam (i) ∑ MB =…

Q: Find scale and units of map 2.Find DATUM & UTM zone

A: Scale of the map as shown in the figure is =1 cm= 1km = 1:10000 Unit of the map is m as the data…

Q: QUESTIONS FOR OUTPUT: In determining the time of setting of hydraulic cement, tabulate the…

Q: A ball decelerates in a straight path at 2.50 m/s2. Determine the distance travelled by the ball…

Q: A factory operates heavy machinery which emits pollutant air with a PM2.5 of 700 ug/m3 . The factory…

A: Rate of PM 2.5 removal = 4 m3/hr Efficiency= 80% PM 2.5 release per hour = 8*700 ug/hr…

Q: The total irrigation depth of water, required by a certain crop in its entire growing period of 150…

A: given- growing period=150 days=150×24×60×60 secdepth of water required=25.92 cm=0.2592…

Q: having an impeller of 35 cm outside diameter rotates at al at exit and are 7 cm wide. The velocity…

A: Given:- diameter=35cm rotates =1000 rpm width=7cm velocity of radial flow=3m/sec velocity in suction…

Q: Draw the shear and bending moment diagrams for each beam loaded as shown. Then, show the computation

A: Given data in question UDL Concentrated moment Point load Span member length To find out SFD BMD

Q: Draw the shear and moment diagram of the loaded beam shown in the figure. Determine the Vmax and…

Q: A differential U-tube manometer is used to measure the change in pressure between two points in a…

Q: if the corrected vertical and horizontal alignment of the sides of the traverse (ABCDE) are as they…

A: To Determine Coordinates of points B,C,D & E

Q: As depicted in figure below, a vertically uniform but laterally sheared coastal current must climb a…

A: Given, H1 = 200 m H2 = 160 m U1 = 0.5 m/ s L1 = 10 km f = 10 − 4 s − 1

Question

PROBLEM 1
Find the moment of inertia of the section with respect to x-axis (lx).
1 m
X
3 m
PROBLEM 2
Find the moment of inertia of the section with respect to y-axis (ly).
1m-
4 m
2
1 m
O

PROBLEM 1
Find the moment of inertia of the section w
| 1 m –
4 m
2
3 m
1 m
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

compute the safe factored uniformly distributed deadload that will be added to the weight of the beam. the beam is simply supported with an span of 6m and carries a uniformly distributed liveload of 20kN/m. use ycon=2 4KN/m³ b=280mm d=415mm fc'=25MPa fy=420MPa As=6-20mm diameter bar the answer is_____KN/m
A tied column shown below is bent in a single curvature about the y-axis. Determine the following if K = 1.0, the column is braced against sidesway, fc’ = 27.6 MPa, fy = 414 MPa, Ec =4700√fc′.a. Critical load ( Pc ) using Euler’s formulab. Moment magnification factor, δbc. Equivalent eccentricity of the column section, e
The simply supported beam consists of a W14 x 34 structural steel wide-flange shape [E - 29,000 ksi; I - 340 in.*]. For the loadingshown, use discontinuity functions to compute (a) the slope of the beam at E and (b] the deflection of the beam at C. Assume wo - 8kips/ft, WCD - 4.5 kips/ft, LAB - 7.5 ft. Lac - 7.5 ft. LCD - 10.5 ft, LDE - 4 ft.W.CD
A UC 305x305x118 steel column supports a single beam framing into its web and connected using a fin plate Steel column web beam.JPG GkA = 159 kN QkA= 193 kN What is the design eccentric bending moment Mz,Ed applied to the weak axis of the column? Give your answer to the nearest kNm and do not include the units in the answer box.
Determine the values of ?bMnx and Mn x/ Ωb for a W18 x 97 with Fy = 50 ksi and an unbraced length Lb = 38 ft. Assume that Cb = 1.0.
the service load bending moments acting on a rectangular beam 333 mm wide and 617mm deep are 139.65kn-m for dead load and 91.15kn-m for live load. f'c=29.99moa fy=414mpa p=0.68pbak db=20mm ds=10mm stirrups are sipral calculate the D/C ratio in percentage
Determine the diameter of a spiral column axially loaded with 1100 kN dead load, and 1000kN live load. Use 28 mm diameter bars, 10mm spirals and steel ratio of 0.02. fc’ = 28MPa; fy=414MPa.
A simply-supported T-beam is subjected to two pairs of distributed loads: pair 1 (wD1, wL1)and pair 2 (wD2, wL2). The geometric, material and loading properties are all given on thetable above. bf=1368mm bw=408mm t=248mm fc'=25.2MPa fy=336MPa d=918mm d'=92mm Lbeam=12.2m wD1=42.2kn/m wL1=50.2kn/m wD2=170.2kn/m wL2=193.3kn/m1. Solve for the height of the compression stress block using pair 1. 2. Solve for the theoretical steel area using pair 1. 3. Using Es = 0.004, solve for the theoretical steel area using pair 2. 4. Using Es= 0.005, solve for the theoretical steel area using pair 2.
Determine the centroidal moment of inertia of the built up section shown using a steel plate 1" x 16" and C-12 x 25 steel section welded together. Refer to the table below. ASAP
Compute the design moment strength of the beam section described below if fy = 420 MPa, fc’ = 21 MPa. d = 650 mm d’ = 70 mm b = 450 mm As’: 3-28mm dia. As: 4-36mm dia
A W 12 a x 72 is used as a column to carry an axial load P. The column has a fixed . oport at the bottom and hinged at the top. The column has an unsupported height of 6m. Using A 36 steel with Fy = 248 MPa. Es = 200000 MPa. Properties of W 12 x 72 A = 13677A0 mm2 d = 311.15 mm bf= 305.82 mm tf = 17.04 nun tw = 10.92 mm Ix = 248.5 x 106 mm4 Iy = 81.17 x 106 mm4 rx = 134.87 mm ry = 77.22 rnm a) Compute the recommended value of the slenderness ratio. b) Compute the allowable compressive stress. c) Compute the allowable axial load P.
solve the problem a) Spacing of stirrups at critical section (d-distance).