Problem 1 There are two identical (very large) tanks of diameter D connected to each other by a pipe of diameter d. Find the velocity of the water in the pipe and the rate of change of water level in each tank when the levels of water in the tanks are and H. Neglect viscous resistance at the inlet and wall of the pipe. Water H Water

Problem 1 There are two identical (very large) tanks of diameter D connected to each other by a pipe of diameter d. Find the velocity of the water in the pipe and the rate of change of water level in each tank when the levels of water in the tanks are and H. Neglect viscous resistance at the inlet and wall of the pipe. Water H Water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two opened tanks filled with water are connected by seriel pipe AB and BC. AB pipe has a diameter of 10cm, and BC pipe is 6cm. The length of pipe for AB is 200m and for pipe BC is 150m. The flow rate of water entering the pipe is 0.007m³/s and coefficient of contraction is 0.62. If the energy losses ONLY occur due to the shock loss at sudden contraction and friction, calculate the level difference of the two tanks. Given f = 0.04 for both pipes.
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe lengthis 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should bethe different in elevation between the upper and lower levels in order to achieve this pressure? Takethe density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.
Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.7 cmWG. The duct diameter is 1.22 m and the barometric pressure is 99.4 kPa and the gage fluid temperature and air temperature is 30 degC. What is the total pressure against which the fan will operate in mm of water? and What is the required motor brake power in Question no. 4 assuming a mechanical efficiency of 89%.
The 100-mmmm-diameter pipe is connected by a nozzle to a large reservoir of air that is at a temperature of 60 ∘C∘C and absolute pressure of 550 kPakPa . The backpressure causes M1>1M1>1, and the flow is choked at the exit, section 2, when L� = 5 mm. Assume a constant friction factor of 0.0085 throughout the pipe. Gas constant for air is R� = 286.9 J/[kg⋅K]J/[kg⋅K] and its specific heat ratio is k� = 1.40. (Figure 1) Determine the mass flow through the pipe. Express your answer using three significant figures.
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.
Two water reservoirs A and B are connected to each other through a 40-m-long, 2-cm-diameter cast iron pipe with a sharp-edged entrance. The pipe also involves a swing check valve and a fully open gate valve. The water level in both reservoirs is the same, but reservoir A is pressurized by compressed air while reservoir B is open to the atmosphere at 95 kPa. If the initial flow rate through the pipe is 1.5 L/s, determine the absolute air pressure on top of reservoir A. Take the water temperature to be 10°C.
A pipe of diameter 40 cm carries a liquid of spec. gravity = 0.94 at a velocity of 24 m/s. The pressuresat points A and B are 294.3 kPa and 224.6 kPa respectively while the elevation head at A and B are 24m and 34 m. Calculate the loss of head between A and B.
A large tank open to the atmosphere is filled with water to a height of 4 m from the outlet tap. A tap near the bottom of the tank is now opened, and water flows out from the smooth and round outlet with a diameter of 25 mm. Determine the water velocity and flow rate at the outlet.
Consider laminar flow through a very long straight section of round pipe, that the velocity profile through a cross-sectional area of the pipe is parabolic with the axial velocity component given by V = 2Vavg(1 − r2/R2) where R is the radius of the inner wall of the pipe and Vavg is the average velocity. Calculate the momentum-flux correction factor through a cross section of the pipe for the case in which the pipe flow rep resents an outlet of the control volume
Water is transported by gravity through a 10-cmdiameter 550-m-long plastic pipe with an elevation gradient of 0.01 (i.e., an elevation drop of 1 m per 100 m of pipe length). Taking ? = 1000 kg/m3 and ? = 1 × 10−6 m2/s for water, determine the flow rate of water through the pipe. If the pipe were horizontal, what would the power requirements be to maintain the same flow rate?
Consider an air solar collector that is 1 m wide and 4 m long and has a constant spacing of 3 cm between the glass cover and the collector plate. Air flows at an average temperature of 45°C at a rate of 0.12 m3/s through the 1-m-wide edge of the collector along the 4-m-long passageway. Disregarding the entrance and roughness effects and the 90° bend, determine the pressure drop in the collector.
A pump is being used to transport a liquid food product (density p=1000kg/m^3, viscosity 0.001 Pa s) from holding tank to filling a machine at a mass flow rate of 2 kg/s. The liquid level in the holding tank is 10 m above the pump, and the filling machine is 5 m above the pump. There is 100 m of 2-in nominal diamter sanitary pipe between the holding tank and the filling machine, wiht one open globe valve and four regular 90° flanged elbows in the system. Within the system, there is a heat exchange which causes 100 kPa of pressure drop due to friction. The holding tank is open to atmosphere, and filling machine is running at a pressure of 1.5 atm. The diamter of the filling machine pipe is 3cm. A: What is the volume flow rate of the system? B: What is the diamete of the pipe? C: What is the average velocity inside the pipe? D: What is the reynolds number of the flow in the pipe? E: What is the flowing type?