Problem 1.12: A journal 25 mm in diameter and supported in sliding bearing has maximum end reaction of 25 kN Assuming allowable pressure 5 N/mm. find length of sliding bearing Solution: Given data:d25 mm, W== 25 KN = 2.5x 10¹ N.

Problem 1.12: A journal 25 mm in diameter and supported in sliding bearing has maximum end reaction of 25 kN Assuming allowable pressure 5 N/mm. find length of sliding bearing Solution: Given data:d25 mm, W== 25 KN = 2.5x 10¹ N.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.5.2P: A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is...

See similar textbooks

Related questions

Q: A bar of circular cross section is to suspend a tank of water 4 ft. below a ceiling. The tank can be…

Q: Consider a long cylindrical solid rod – total length L – mass density p; – radius R1 = R2 = R; -…

Q: A solid circular bar is surrounded by a layer of copper rigidly attached to it, the assembly is…

Q: A weight is suspended from two wires. One wire is steel and the other aluminium. The elastic modulus…

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…

A: Given Data: The decrease in total length is, δH= -0.68 mm. The elastic modulus of steel is, E=206…

Q: The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional…

Q: GIVEN: 80 kN 30 kN/m 3 m- 2m 2m FIND: Solve for the internal forces at (a) 0.5m, (b) 1m, (c) 3m, &…

Q: • Dimensions: width, b = 54 mm, depth, d = 110 mm, and height, h = 284 mm. • The modulus of…

Q: round bar of length L. modulus of elasticity E, and weight density tapers uniformly from a diameter…

A: Given:Length of round bar=L,Modulus of elasticity= E,Weight density=γ,Diameter at one end=3DDiameter…

Q: Q/ Find the number of steel bars for a rectangular foundation and support an interior column of…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at…

Q: For the system shown in Fig. 1, determine the generalized physical properties m", c", k", and the…

A: We have to calculate the m,k,c explaining with physical properties and Dimensions

Q: With pressure steel tank axis α = 750 manufactured as degree angle helical welded references Tank…

Q: A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and…

Q: A Belleville spring is made of silicon steel. The spring is compressed completely fl at when it is…

A: Given Force = 4500 N Allowable stress = 1375 × 106 N/m2 do/di =1.75 h/t = 1.5 To find Thickness of…

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: Question cm is subject to 4 forces of 1 kN each applied at the edges of the plate with a 45-degree…

A: First of all we have to resolve these forces along x and y axes. The inclined forces then becomes…

Q: A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a…

A: a.

Q: 1-A bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here.…

A: Given data: Modulus of elasticity, E = 166 GPa. Draw a labeled diagram of the given bar. Apply…

Q: Problem: 75 mm diam. shaft 12,000 N 16,000 N 900 mm 900 mm 900 mm 900 mm 4,000 N R, 300 mm 20,000 N…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: A rigid strut ABCD supports two concentrated loads P at points B and D. It is being supported by a…

A: Given: The area of cable, A = 120 mm^2 = 120 x 10-6 m2 The elastic modulus of the cable, E = 50 GPa…

Q: A spherical shell of volume mass density p, thickness t and radius R(R>>t) is placed concentrically…

Q: Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ =…

A: Given data: d=2.9 inE1=10000 ksiE2=17000 ksiL1=80 inL2=110 inδ=0.10 in Need to determine the…

Q: 50 kN 30 kN A 2 m 1 m 3 m

A: For solution refer below images.

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…

A: Given ∆LAC=0.72mmE=223 MPa=223 N/m2=223 ×10-4 N/cm2H1=LAB=7 cmH2=LBC=10 cmArea of bar AB=AAB=2×2=4…

Q: An unknown weight falls by 30 mm onto a collar rigidly attached to the lower end of a vertical bar 4…

Q: or the two-cell tube, the rate of twist is 5 degree/meter. G=20 GPa, if a is 10 cm and t equals to 4…

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

Q: Example 4.2. A beam 3 m long weighing 400 N is suspended in a horizontal position by two vertical…

A: Given data: Length of the beam (L) = 3 m Weight of the beam = 400 N Weight of the body = 200 N Need…

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has…

Q: The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter.…

Q: Problem 1. For the grid shown in Figure below, determine the nodal displacements and the local…

A: Given: Let us consider the given data, E=30×106 psiG=12×106 psiI=200 in4J=100 in4d1y=ϕ1x=ϕ12=0d3y=0…

Q: Find the hoop stress acting on a cylinder with the following information: D= 40 cm in diameter. wall…

Q: A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is…

A: Given data, External diameter, do = 250 mm Thickness of the cylinder, t = 5 mm Internal diameter of…

Q: to applied force P = 10 kN. For simplicity, assume AE = 1 for all members. 4 m 4 m 4 m

Q: F2 (2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum…

A: Write the given value using suitable variables. Here ΔlC signifies point C axial displacement, F2…

Q: Consider the vessel in which the wall thickness of the cylindrical and hemispherical portions has a…

Q: SET B: For the spring shown below, find the maximum stress. d = 5 mm D = 0.4 m F = 50 N D

Q: 3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the…

Q: Question 1 cm is subject to 4 forces of 1 kN each applied at the edges of the plate with a 45-degree…

Q: Bligh's and Lane's theory For the hydraulic structures shown below calculate 1- Sketch the HGL from…

A: From the given data,

Q: A uniform tubular pipe 100ft long and weighing 55lbs is supported by a fulcrum as shown in the…

Q: A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a…

A: GivenM=15000Nm=11000N

Q: Problem 2. Each segment of bar ABC has length Z. and shear modulus G7 and both segments have solid…

A: To find: (a) The torque at A and C. (b) The twist angle ϕB at point B. Given: The length of each…

Q: The 100-cm long shaft CD is subjected to the loading shown in Fig. 4, supported by a journal bearing…

Q: A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented…

Q: wood-stave penstock of 1.8 m diameter is wrapped with steel hoops and subjected to a fluid pressure…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The Figure shows a bar AB, of length L, which is supported at point A, against the wall andsuspended by a cable at point B, and a weight w is hung from it at end B. The weight of thebar AB and cable weight are negligible. Suppose the weight W and the angles θ1 and θ2are known. What is the direction of the reaction force R of the wall against the bar
A round bar of length L. modulus of elasticity E, and weight density tapers uniformly from a diameter of 3D at one end to a diameter 2D at the other end. If the bar is suspended vertically from the larger end, find the elongation of the bar caused by its own weight.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
The figure shows the cross section of three cylinders, 1m long, given the density of steel 500 lbs/cu.ft. Find the reactions between all of the cylinders and the ground in lbs. Units are in feet.
A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0,respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the leftend where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) andthe weight (W) of the bar
A uniform bar 6 m long is held by ropes at the ends making angle 60° and 30°, respectively, with the horizontal. A weight of 400 N is hung 1.0 m from the left end where the 60° rope is attached. Find the tension in the rope and the weight of the bar.
A uniform, 7.5-m-long beam weighing 6490 N is hinged to a wall and supported by a thin cable attached 1.5 m from the free end of the beam. The cable runs between the beam and the wall and makes a 40° angle with the beam. What is the tension in the cable when the beam is at an angle of 30° above the horizontal?
Two ladders, 4.00 m and 3.00 m long, are hinged at point A and tied together by a horizontal rope 0.90 m above the floor (Fig. ). The ladders weigh 480 N and 360 N, respectively, and the center of gravity of each is at its center. Assume that the floor is freshly waxed and frictionless. (a) Find the upward force at the bottom of each ladder. (b) Find the tension in the rope. (c) Find the magnitude of the force one ladder exerts on the other at point A. (d) If an 800 N painter stands at point A, find the tension in the horizontal rope.
1. A prismatic bar AE of negligible weight is hinged to a vertical wall at A and supported by a strut BD as shown in Fig. 1. Find the reaction induced at A and B through the action of a sphere of weight W tied by a string CF that is parallel to AE. Also, find the tension in the string. The radius of the sphere is such that the points B and C are at the same level. Assume W = 1000 lb.05:54 PM
the bent bar AB weighing 10lb/ft is mounted as shown in figure 2 upon a carriage weighing 250 lb. The center of gravity of the carriage is at C midway between the wheels. If P=108lb and there is no frictional resistance at the wheels, find the wheel reaction R1. find the vertical component of the hinge force at A. find the horizontal concept of the hinge force at A.
4. A 15,000 N crane pivots around a friction-free axle at its base and is supported by a cable making a 25° angle with the crane (see figure below). The crane is 16 m long and is not uniform, its center of gravity being 7.0 m from the axle as measured along the crane. The cable is attached 3.0 mfrom the upper end of the crane. When the crane is raised to 55° above the horizontal holding an 11,000N pallet of bricks by a 2.2 m, very light cord, find (a) the tension in the cable and (b) the horizontal andvertical components of the force that the axle exerts on the crane.
A metal bar 10 m long and weighs 50 N is supported at the 7 m mark by a fulcrum. A 100 N bag is suspended at the right end of the bar. Where should a 40 N weight be suspended to balance the bar?