Problem 10.24A cast iron pipe having a diameter of 100 mm is used to fill the cylindricaltank with water at T = 25°C. The pipe has a total length of 50 m. Supposethat h = 22.5 m. Neglect minor losses. Use the equation# = -1.8 log(Figure 1)Figure€/D 1.11 6.9+3.7Re2m1 of 1Part ADetermine the required power output of a pump necessary to fill the empty tank to a depth of 3 m in 6.5 min.Express your answer to three significant figures and include the appropriate units.out =SubmitProvide FeedbackμAValueRequest AnswerUnits?3 of 6Review>Next >

Given Height 22.5 mTemperature 25°CLength 50 mDiameter 100 mmDepth 3 mTime 6.5 minutes To find out…

Problem 10.24 A cast iron pipe having a diameter of 100 mm is used to fill the cylindrical tank with water at T = 25°C. The pipe has a total length of 50 m. Suppose that h = 22.5 m. Neglect minor losses. Use the equation = -1.8 log (Eigure 1) Figure (e/D 1.11 6.9 + 3.7 Re WW 2m 1 of 1 > ▾ Part A Determine the required power output of a pump necessary to fill the empty tank to a depth of 3 m in 6.5 min. Express your answer to three significant figures and include the appropriate units. Wout= Submit Provide Feedback ¹μÅ] 1 Value Request Answer С Units ? 3 of 6 Review Next >

Problem 10.24 A cast iron pipe having a diameter of 100 mm is used to fill the cylindrical tank with water at T = 25°C. The pipe has a total length of 50 m. Suppose that h = 22.5 m. Neglect minor losses. Use the equation = -1.8 log (Eigure 1) Figure (e/D 1.11 6.9 + 3.7 Re WW 2m 1 of 1 > ▾ Part A Determine the required power output of a pump necessary to fill the empty tank to a depth of 3 m in 6.5 min. Express your answer to three significant figures and include the appropriate units. Wout= Submit Provide Feedback ¹μÅ] 1 Value Request Answer С Units ? 3 of 6 Review Next >

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Given the properties and elevations of the three reservoirs, if friction factor f, is 0.01 for all pipes,determine the followinga. Energy head at junctionb. Head loss of pipe-1c. Discharge of pipe-3
5.10 The water is supplied at the rate of 3 m3 per minute from a height of 4 m to a hydraulic ram, which raises 0.3 m3/minute to a height of 30 m from the ram. The length and diameter of the delivery pipe is 100 m and 70 mm respectively. Determine the D' Aubuisson's efficiency of the hydraulic ram if the co-efficiency of friction f = .009.
A pump is used to raised water to a reservoir through 1000 m. long of 20 cm diameter with Cw of Hazen-William's Equation equal to 100. If the pipe is to be replaced with a new one having the same length but with a diameter of 25 cm and Cw= 120, determine the power save if the flow is to be maintained at 75liters per second. Draw the approximate EGL and HGL
A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
A pump is used to raised water to a reservoir through 800 m. long of 20 cm diameter with Cw of Hazen-William’s Equation equal to 110. If the pipe is to be replaced with a new one having the same length but with a diameter of 25 cm and Cw = 130, determine the power save if the flow is to be maintained at 100 liters per second. Draw the approximate EGL and HGL.
Given the properties and elevations of the three reservoirs, if friction factor f, is 0.01 for all pipes, determine the following a. Energy head at junction b. Head loss of pipe-1 c. Discharge of pipe-3
Two reservoirs (EI 37.6m and EI 91.6m) are connected by two pipelines 1-2 and 2-3 with a pump bridging the two pipelines. If the fluid (sg=0.81) flows at a rate of 203 L/s, what is the power given by pump? Assume head losses of 2.3 j/n from 1-2 and 6.5 j/n from 2 to 3
1. Compute the head loss in a pipe with diameter 300 mm for a length of 15,000 meters and carrying a flow of 0.097, if f=0.02. (Hint: Use h=(0.0826fL(Q^2))/(D^5)
If the total flow of 4.0m3/? takes place in the three pipes. Determine the distribution offlow. The pipe lengths, diameters and frictions factors are shown below.
Two reservoirs are connected by three pipes. laid in parallel. The pipes diameters are respectively 10cm, 20cm and 30cm and they are of the some length. If discharge through 10cm pipe is 0.1 m3/s, calculate the discharge through the larger pipes. Assume the friction coefficient ‘f’ to be same for the pipes.
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.