Problem 13-28 The mine car of mass mcar is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F = bi². If the car has an initial velocity vo when t = 0, determine its velocity when t = t]. Given: M mcar = 400 kg b = 3200 m vo = 2 tį = 2 s m g = 9.81 c = 8 d = 15

Problem 13-28 The mine car of mass mcar is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F = bi². If the car has an initial velocity vo when t = 0, determine its velocity when t = t]. Given: M mcar = 400 kg b = 3200 m vo = 2 tį = 2 s m g = 9.81 c = 8 d = 15

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.5P: The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the...

See similar textbooks

Similar questions

Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
1)Calculate the velocity of the arm, observed by a stationary person on the ground.2)Draw the FBD of the combined body (crane body, arm and load).3)Is the combined body stable? Why?4)Calculate the moment of the following, about wheel A,i) combined crane bodyii) load mass5)Which combined body’s component(s) will not fail? Why? (Hint: The crane was initially in equilibrium.)6)What are the various limits (maximum or minimum) for the combined body to be stable? Explain why.
A stationary bicycle wheel of radius 0.7 m is mounted in the vertical plane (see figure below). The axle is held up by supports that are not shown, and the wheel is free to rotate on the nearly frictionless axle. The wheel has mass 4.3 kg, all concentrated in the rim (the spokes have negligible mass). A lump of clay with mass 0.5 kg falls and sticks to the outer edge of the wheel at the location shown. Just before the impact the clay has speed 8 m/s, and the wheel is rotating clockwise with angular speed 0.27 rad/s. Assume +x is to the right, +y is upward, and +z is out of the page. Assume the line connecting the center to the point of impact is at an angle of 45° from the horizontal.Just after the impact, what is the angular velocity (magnitude and direction) of the wheel?
Write an expression for how far the spring is stretch when the cart is at rest in the equilibrium position. Name thisdistance y-naught. Thanks!
The instrument of mass 50 kg is meant for impact on a surface. The impact velocity 10m/sec. Inside the mounting the system has a stiffness of 5 N/m and C=1 Ns/m . find maximum displacement of the instrument afterr engaging the spring and damper
The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant: 3.1. Draw the port governor mechanism and clearly lable it. (06)3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.
Obtain the equation of motion by drawing the free body diagrams of the given system.
Solve Sample Prob. 4.5, assuming that the spring is unstretched when 0 = 90°.(Reference to Sample Problem 4.5):
A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. Themaximum belt tension is not to exceed 620 N and it is required to transmit 1·8 kW at anoutput speed of 360 rev/min. Determine:(a) The input torque. (b) The belt speed. (c) The limiting slack side tension. (d) The initial tension at which the belt should be set.
The collar is released from rest in the position shown and slides down the fixed rod. Calculate (a) the stiffiness k of the spring (which has been initially pre- compressed 50 mm by the light strap and wires) so that its maximum additional deflection equal 190 mm. (b) The nomal force N between the rod and the collar at 10 kg 190 the end position. Uj-2= AT
The 13-kg sphere C is released from rest when θ = 0∘ and the tension in the spring is F = 100 N. The figure shows rod AB hinged at point A. Sphere C is attached to the other end of the rod, labeled as B. Point D is located on the rod, 0.3 meters from point A and 0.15 meters from the center of the sphere. A spring with stiffness k of 500 newtons per meter is attached to the rod at point D by one of its ends. Another end of the spring is fixed at point E, located 0.4 directly above point A. The sphere is shown to be below and to the right of point A. An acute angle between the rod and the horizontal is labeled as theta. Determine the speed of the sphere at the instant θ = 90∘ . Neglect the mass of rod AB and the size of the sphere.