Problem 18.1 A steel mount supports a force P from vibrating equipment. In order to partially isolate the vibration from other areas of the building, rubber mounts are used to connect the steel bracket to the concrete wall. There are two identical mounts, one on each side of the bracket. The mount dimensions are t = 0.6in, b=2in, and w = 4in where w is the third dimension, into the page. The mount material has a shear modulus G=3000psi. Determine the force P that corresponds to a 0.1 inch displacement of the connecting frame.

Problem 18.1 A steel mount supports a force P from vibrating equipment. In order to partially isolate the vibration from other areas of the building, rubber mounts are used to connect the steel bracket to the concrete wall. There are two identical mounts, one on each side of the bracket. The mount dimensions are t = 0.6in, b=2in, and w = 4in where w is the third dimension, into the page. The mount material has a shear modulus G=3000psi. Determine the force P that corresponds to a 0.1 inch displacement of the connecting frame.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The crankshaft-flywheel assembly of a large engine may be considered a torsion pendulum. The shaft is 1.8m long and transmit 179.127kN-m torque corresponding to 83MPa stress. The flywheel diameter is 75cm and weighs 4.5kN. If the modulus of rigidity of the shaft material is 77GPa, compute the period of vibration of this system.
The rotation in degrees of a shaft, 800 mm long subjected to atorque of 80 N-m, 10 mm in radius and shear modulus of 85 GPais
As shown in the figure, a homogeneous 100-kgrigid block is suspended by the three springs whoselower ends were originally at the same level. Eachsteel spring has 24 turns of 10-mm-diameter on amean diameter of 100 mm, and G = 83 GPa. Thebronze spring has 48 turns of 20-mm-diameterwire on a mean diameter of 150 mm, and G = 42GPa. Compute the maximum shearing stress ineach spring using A.M. Wahl formula.
A bar of dimension 130 mm x 50 mm x 45 mm, is subjected to an axial pull of 90 kN. The measured extension is 0.1 mm and change in depth is 0.003 mm. Calculate: (i) Young’s Modulus, (ii) Poisson’s ratio (iii) Shear Modulus. and (iv) Bulk Modulus (i) The Young's modulus is (N/mm2) = _________________ (ii) Poisson's ratio = ___________________ (iii) The shear modulus is (unit in N/mm2) = ________________ (iv) The Bulk modulus is (unit in N/mm2) = ________________
A thin copper tube, 14 mm internal diameter and 0,5 mm wall thickness has closed ends and rotates at 1200 r/min while it is subjected to an internal gauge pressure of 222 Pa. Calculate the total hoop stress in the wall of the tube if the density of copper is 8900 kg/m3.
A steel bar 25 mm wide and 50 mm deep is simply supported at two points 3 m apart andcarries three loads of 1000 N, 1500 N and 750 N at 1 m, 2 m and 2.5 m from the leftsupport. The Young's modulus for steel is 200 GPa. If the mass of the bar is 262 kg/m,find the frequency of transverse vibration.
A bar of dimension 130 mm x 50 mm x 45 mm, is subjected to an axial pull of 90 kN. The measured extension is 0.1 mm and change in depth is 0.003 mm. Calculate: (i) Young’s Modulus, (ii) Poisson’s ratio (iii) Shear Modulus. and (iv) Bulk Modulus (i) The Young's modulus is (N/mm2) = _________________ (ii) Poisson's ratio = ___________________
A shaft 1.5 m long is supported in flexible bearings at the ends and carries two wheels each of 50 kg mass. One wheel is situated at the centre of the shaft and the other at a distance of 0.4 m from the centre towards right. The shaft is hollow of external diameter 75 mm and inner diameter 37.5 mm. The density of the shaft material is 8000 kg/m3. The Young’s modulus for the shaft material is 200 GN/m2. Find the frequency of transverse vibration.
A copper wire, caliber 16 AWG (diameter of 0.1019 in.) 4 ft in length, is stretched with a force of 500 lb. It lengthens 0.21 in. and its diameter is reduced 0.10175 in. Determine the modulus of elasticity, from its response in 10^3 ksi.
4a This is for my reviewer only please help me with the step by step solution and answer, thank you What is the value of the obective function when x=8 ; y=0 and the slack vqriable are 4 and 0?
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
A 500 kg box is suspended with a rope and pulley arrangement. Indicate the required intensity and direction for the "T" force. (Use the sine and cosine theorems to solve the problem.)