Problem #2 Design a footing to support an 18 in. square column tied interior column reinforced with 8 #9 bars. The column carries an unfactored axial dead load of 245 kips and an axial live load of 200 kips. The base of the footing is 4 ft. below final grade and allowable soil pressure is 5 k/ft2 Use f' 3.0 ksi and fy 60.0 ksi. Limit one side of the footing to 8.5 ft.

Problem #2 Design a footing to support an 18 in. square column tied interior column reinforced with 8 #9 bars. The column carries an unfactored axial dead load of 245 kips and an axial live load of 200 kips. The base of the footing is 4 ft. below final grade and allowable soil pressure is 5 k/ft2 Use f' 3.0 ksi and fy 60.0 ksi. Limit one side of the footing to 8.5 ft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design the two footings and the strap beam that can supports an exterior column (400 mm square) and internal column of (600 mm square) placed at a distance center to center equal to 7 m. The exterior column having its face along the property line carries a DL = 500 kN and LL = 450 kN, while the interior column carries a DL = 900 kN and LL = 700 kN. The bottom of the footing is to be 1.8m below the grade. Allowable soil bearing capacity is 210 kPa. Assume e=1.5m, f’c = 20.7 MPa, and fy = 415 MPa. Use 75 mm steel cover and 25 mm Ø main bars and for the strap beam; b=600mm and 12 mm Ø for stirrups with fyt=276MPa.
A certain column carries a vertical downward load of 1,200 kN. It is to be supported on a 1 mdeep, square footing. The soil beneath this footing has the following properties: g = 20.5 kN/m3, c′ = 5 kPa, and f′ = 36o . The groundwater table is at a depth of 1.5 m below the ground sur-face. Using ASD, compute the footing width required for a factor of safety of 3.5.
A central column 300 mm x 300 mm dimension in a three storey building is to support a service load of 548 kN. If the allowable bearing pressure is 150kN/m2. Design an appropriate footing using fcu= 25 N/mm2 and fy= 410 N/mm2. Assume a load factor of 1.45. Do all the necessary checks and sketch the requirements details.
A 4 ft square, 2 ft deep spread footing carries an ASD design column load of 50 k. The edge of this footing is 1 ft behind the top of a 40 ft tall, 2H:1V descending slope. The soil has the fol-lowing properties: c′ = 200 lb/ft2 , f′ = 31°, g = 121 lb/ft3 , and the groundwater table is at agreat depth. Compute the ASD factor of safety against a bearing capacity failure and commenton this design.
A 5 ft square, 2 ft deep spread footing is subjected to a concentric vertical load of 60 k and anoverturning moment of 30 ft-k. The overturning moment acts parallel to one of the sides of thefooting, and the top of the footing is flush with the ground surface and the groundwater tableis at a depth of 20 ft below the ground surface. Determine whether the resultant force actswithin the middle third of the footing, compute the minimum and maximum bearing pressuresand show the distribution of bearing pressure in a sketch. Determine the size of the equivalentuniformly loaded footing and compute the equivalent bearing pressure.
RECTANGULAR COMBINED FOOTING: Two columns are 5.5 meters away from each other. The dimensions and loads supported by each column are listed below (see image). The net allowable soil bearing capacity is 140 kPa. Use f'c=28MPa and fy=275MPa. Note: The 0.45-m column dimension is along the length of the footing. Design a combined footing that will support the two columns.
A square footing is to be designed to support a column. The design loads on the columnare all downward and concentric. Calculations of the design loads using the required loadcombinations specified by ASCE 7-11 show that the controlling load combination givesa design column load of 450 k. The embedment depth of the square footing is to be 3 ft.The underlying soil has an undrained shear strength of 2,000 lb/ft2 and a unit weight of 109 lb/ft3. The groundwater table is at a depth of 4 ft. Using the ASD method, determinethe minimum required footing width to maintain a factor of safety of 3 against a bearingcapacity failure.
A 200 mm wide concrete block wall carries a factored vertical design load of 172 kN/m. Thesustained load for settlement is 130 kN/m. It is to be supported on a continuous footing madeof 18 MPa concrete and 280 MPa steel. The soil has an allowable bearing pressure for bearingcapacity of 180 kPa (using LRFD methods) and an allowable bearing pressure for settlement of 110 kPa. The groundwater table is at a great depth. The local building code requires that the bot-tom of this footing be at least 500 mm below the ground surface. Determine the required footing, width, thickness, and design the lateral and longitudinal steel. Show your design in a sketch.
A 400 mm square concrete column reinforced with eight metric #19 bars carries vertical dead and live loads of 980 and 825 kN, respectively. It is to be supported on a 2.0 m * 3.5 m rect-angular footing. The concrete in the footing will have f′ c = 20 MPa and fy = 420 MPa. Thebuilding will have a slab-on-grade floor, so the top of the footing must be at least 150 mm belowthe finish floor elevation. Develop a complete structural design, including dowels, and show itin a sketch.
ASAP PLS I GIVE UPVOTE If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column has a 1.1m height from the top of the footing up to the finished ground line are both constructed, how much gravel (in m3) should be exactly used for a class B concrete mixture for the footing and the column (up to the finished ground line level).
A column carrying a vertical downward unfactored load of 270 k is to be supported on a 3 ft deepsquare spread footing. The soil beneath this footing is an undrained clay with su = 3,000 lb/ft2and g = 117 lb/ft3 . The groundwater table is below the bottom of the footing. Using the ASD method, compute the width B required to obtain a factor of safety of 3 against a bearing cap-acity failure.
A square footing is to support a 400mm x 400mm tied column that carries a service dead load of 880 kN and a service live load of 710kN. The column is reinforced with 8-25 mm diameter bars. The base of the footing is 1.5 meter below the natural grade line where the soil bearing capacity is 235 kPa. The soil above has a unit weight of 15.6 kN/m³. Using fy=275 MPa, f’c=27.5 MPa, and unit weight of concrete of 23.5 kN/m³. Assume footing depth of 600 mm for soil bearing pressure. Use U = 1.2D + 1.6L 1. Determine the footing dimensions in whole cm. a. 450 b. 320 c. 280 d. 400 2. Determine the depth of footing computed from one way shear in whole cm. a. 35.88 b. 34.25 c. 32.56 d. 44.36 3. Determine the depth of footing computed from punching shear in whole cm. a. 35.42 b. 34.25 c. 32.56 d. 48.30