help asap 3decimal places PROBLEM 2: The tank contains a liquid having a densityas shown.25cm1.5 m3 m2 mPliquid = 1.3 Mg/m³ a. Determine the unit weight of the liquid when it is at the level shown.Express your answer in SI units. Indicate the appropriate unit. *Your answerb. Determine the weight of the liquid. Express your answer in SI units.Indicate the appropriate unit.*Your answwerC. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured%3Dinto the tank, *It will sink to the bottom of the tankIt will float on the surface of the liquid.It will be suspended in the liquid.

Internal dimensions of box = 3m * 1.5m * 2mDepth of water = 2-0.25 =1.75mDensity of liquid, ρliquid…

Answered: PROBLEM 2: The tank contains a liquid…

Engineering

Civil Engineering

PROBLEM 2: The tank contains a liquid having a density as shown. 25cm 1.5 m 3 m 2 m Pliquid = 1.3 Mg/m³ %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: An increase in pressure of a liquid from 7.5 MPa to 15 MPa results into 0.2 percent decrease in its…

A: Given: The increase in pressure of a liquid is 7.5 MPa to 15 MPa. The decrease in volume is 0.2%.

Q: A liquid has a relative density of 0.8 and a kinematic viscosity of 2.3 centistoke. Determinets: (i)…

Q: Calculate the flux of water through MF and UF membranes operating at 1 bar pressure and 298 K.…

Q: A sound wave is observed to travel through a liquid with a speed of 1400 m/s. The specific gravity…

Q: 1-67. Sand grains fall a short distance into a tank of benzene. Determine the largest average…

Q: kgs, respectively. Calculate the percentages of water at FC and hygroscopic water.

Q: A cube of metal with a height of 5.25 meters on each side floats in water. The specific gravity of…

Q: A glass sphere (Rd= 2.7) 1 mm in diameter is observed to have a fall velocity of 1.25 cm/s in an oil…

A: The viscosity is a measure of the resistance of fluid to flow. It defines the friction within a…

Q: 1 kg of water has a bulk modulus of 2.4 GPa. Determine the percentage reduction in volume if the…

Q: Question 3 A reservoir with an outer radius of 400 m, an inner radius of 2.5 m, and a height of 15 m…

A: As per our guidelines we have to give one answer at a time. Compressibility of reservoir is given…

Q: Refer to the constant-head arrangement shown in Figure 7.5. For a test, the following are given: L =…

A: WE KNOW RELATIONk=QLAhtQ=total volume of waterL=lengthA=Area of cross-sectionh=headt=time

Q: The base of a solid metal cone (Sp. Gr. 6.95) is 25 cm in diameter. The altitude of the cone is 30…

A: Given, SG of cone = 6.95 Diameter of cone = 25 cm Height of cone = 30 cm

Q: This is a hemispherical shell filled with water. Radius of hemispherical shell = 2 m Diameter of…

Q: Mercury (density = 13600 kg/m³, o = 0.49 N/m, 0 = 0°) is contained in a wide beaker. A 2 mm internal…

Q: A liquid flows down an inclined plane surface, where the plane moves with a speed U in the nagtive x…

Q: There is a capillary action that takes place above the groundwater table up to 1.3 m in height.…

Q: If the specific weight of a liquid at 0 degree Cis 9810 N/m3 and its kinematic viscosity is…

A: Given data, Specific weight of liquid = 9810 N/m³ Kinematic viscosity = 1.79 *10^-6 m²/s Density =…

Q: llustrate in one figure the different mechanical layers of the eart

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A section of a gravity dam made of Martian regolith is shown in the figure. The dam is located in a…

Q: Problem 3 A soap bubble 62.5 mm diameter has an intenal pressure in excess of the outside pressure…

A: The pressure inside the soap bubble is higher than that of external/atmospheric pressure due to the…

Q: In a laboratory test of an aquifer material a fully saturated sample of volume 5 liters was taken…

A: Solution:

Q: The bulk modulus of water is 2.0 x 10° N/m². The pressure required to increase the density of water…

A: Bulk Modulus of water =2×109 N/m2

Q: The bulk modulus of water is 210x10 kN/m². What pressure is required to reduce the volume of water…

Q: Which of the following statements are TRUE, when the cavitation parameter o = 0? 1. The local…

A: There is missing information in the first question because three options are correct for this…

Q: A confined aquifer of 15 m constant thickness is sandwiched between two aquicludes as shown in the…

A: Given- Heads= 55.2 m & 34.1 mk=80 m/dayporosity n=0.25time taken to reach from P to Q is needed…

Q: The pressure 27 meter below a liquid is 772.64 kPa, determine its mass density (kg/m³).

Q: Draw the linear graph for liquid limit determination

A: Liquid Limit: The minimum water content at which the soil has tendency of flow is the liquid limit…

Q: A cube of metal with a height of 6.84 meters on each side floats in water. The specific gravity of…

Q: The pressure 44 meter below a liquid is 345.05 kPa, determine its mass density (kg/m).

Q: The maximum diameter that a capillary tube can have to ensure that a capillary rise of atleast 6 mm…

Q: 1.) A volume of 3 cu. meter of water is subjected to a pressure increase of 17 MPa Compute the…

Q: 1 m in a vessel of cross-sectional area 0.04 m2 . The mass of solids in the bed is 50 kg and the…

A: Given:- A packed bed of solid particles of density 2500 kg/m3 occupies a depth of 1 m in a vessel of…

Q: 1. Find the depression h of the mercury in the glass capillary tube having diameter of 2mm if the…

Q: A water main 160 cm dia. contains water at a pressure head of 200 m. Take weight of water to be 1000…

A: The given data is: Diameter=160 cm Pressure head=200 m Permissible stress=400 kg/cm2

Q: The liquid in blue color has a density of 500 kg/m. Calculate the gage pressure Pain kpa for h = 5…

A: Given Density = 500 kg/m3 Height = 5 m We need to find PA

Q: SHOW COMPLETE AND CLEAR SOLUTION. SHOW FREE BODY DIAGRAM (FBD) A dam structure with a base of 18…

Q: A cube of metal with a height of 5.93 meters on each side floats in water. The specific gravity of…

A: Given data in question Cube side Water Specific gravity To find out Submerged depth

Q: 24.For the tank shown in the Figure, hi = 3m and h3 = 4 m Determine the value of h2. %3D

A: Given: h1 =3m, h3 = 4m and Specific gravity of oil = 0.84 Find: h2= ?

Q: A liquid flowing from a reservoir thru a non-rigid 600 mm diameter pipe with a velocity of 2.5 m/s…

A: The formation of the water hammer effect in the water carrying pipes are governed by two different…

Q: 2. If the specific weight of a liquid is 8.0 kN/m³, find its density and specific gravity.

A: We know that ; Specific weight = Density X gravity (g) So, Density = Specific weightg Substituting…

Q: in water and explain how the two can be equal in a given sample of water.

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: An oil of sp. gr. 0.9 is contained in a vessel. At a point the height of oil is 40 m. Find the…

A: Given, Oil of specific gravity = 0.9 Height of oil = 40 m Find, Corresponding height of water (hw)…

Q: 9. For liquid fluids will capillarity rise (or fall) increase or decrease with rise in temperature.…

A: Capillarity is a phenomenon of rise of liquid through a tube because of surface tension.

Q: Example 10: A 40-lb, 0.8-ft-diameter, 1-ft-tall cylindrical tank slides slowly down a ramp with a…

A: given data:- weight of water tank=40lb diamenter=0.8ft hight of tank=1ft speed=0.1ft/sec…

Q: 1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has…

Q: 1.3 A liquid at 20°C has a relative density of 0.80 and a kinematic viscosity of 2.3 centistoke.…

Q: A liquid has an absolute viscosity of 2.231025 Ib-s/ft. It weighs 45 Ib/ft'. What is its kinematic…

A: solution Given absolute viscosity μ=2.231025 lb-sft21pas -sec =147.88 lb-sft2 so μ=2.231025×47.88…

Q: The ocean's pressure at a depth of 9.9 km is 7a,bc MPa. Recognizing that the unit volume weight of…

Question

help asap 3decimal places

PROBLEM 2: The tank contains a liquid having a density
as shown.
25cm
1.5 m
3 m
2 m
Pliquid = 1.3 Mg/m³

a. Determine the unit weight of the liquid when it is at the level shown.
Express your answer in SI units. Indicate the appropriate unit. *
Your answer
b. Determine the weight of the liquid. Express your answer in SI units.
Indicate the appropriate unit.
*
Your answwer
C. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured
%3D
into the tank, *
It will sink to the bottom of the tank
It will float on the surface of the liquid.
It will be suspended in the liquid.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given details

VIEW

Calculations & results

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference ?????? ?????−???? ?????= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
A slurry behaving as a pseudoplastic fluid is flowing through a smooth round tube having an inside diameter of 5 cm at an average velocity of 8.5 m/s. The density of the slurry is 900 kg/m3 and its flow index and consistency index are n=0.3 and k=3.0Ns0.3/m2. Calculate the pressure drop for 50 m length of vertical pipe with the flow moving against gravity.
6. Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown in figure. Determine the pressure difference Pfresh water- Psea water= ?(kPa) between the two pipelines. Take the density of seawater at that location to be P = 1035 kg/m³. (2 decimal)
A tank shaped in a frustum of a cone has a lower base radius 1 m, upper base radius 0.50 m and an altitude of 10 m. It is filled with water to a depth of 4 m. The water is then transferred to a spherical tank with radius 5 m. What is the depth of the water in the second tank in meter?
A concrete dam is going to be built on a silty/clayey sand stratum as shown in Figure 1 to provide a water reservoir. The total length of the dam is 100 m. What is the minimum factor of safety against boiling at the exit point? A. 0.95 B. 1.41 C.1.73
A sphere 1 m in diameter floats half submerged in a tank of liquid (sp.gr = 0.80). a) What is the weight of the sphere?, b) What is the minimum weight of the anchor (sp.gr. = 2.40) that will required to submerged the sphere completely?
A liquid (? = 850 kg/?3; ? = 1.7 × 10−1 Pa ∙ s) flows tangentially past a flat plate. If the free stream velocity is 2 m/s, what is the velocity 5 m downstream from the leading edge of the plateand 15 mm away from the plate.
A conical tank 4.5m on top and 4,7m tall has a 60mm diameter orifice at its bottom for its outlet. Assume C = 0.63. The tank is filled with 7000 liters of water. What is the depth of the water in the tank in meters? How long will it take to drain the content of the tank in minutes? show solution and diagram
The outflow channel shown in Figure 10.10 is about 10 km across and 100 m deep. If itcarried 107 metric tons (1010 kg) of water per second, as stated in the text, estimate thespeed at which the water must have flowed
USING FOL Differential Equation APPLICATION SOLVE THE FOLLOWING PROBELM AND SHOW COMPLETE SOLUTION AND FINAL ANSWER.In a tank of 100 liters of brine containing 50 kg total dissolved salt. Pure water is allowedto run into the tank at the rate of 3 liters a minute. Brine runs out of the tank at the rateof 2 liters a minute. The instantaneous concentration in the tank is kept uniform bystirring. How much salt is in the tank at the end of 1hour?
a cylindrical tank 2m in diameter and 1.5 m high floats with a draft of 1m. compute the time necessary to sink it to its top edge by opening a standard orifice, 5cm diameter in its bottom. neglect the thickness c=0.62
The parameters of the Horton equation are fo = 7(cm/st), fc = 1 (cm/st) and the coefficient k = 4 (1/st¹). Accordingly, the total water leaking from an area of 2 ha to the ground in a day (24 hours) find its volume.