Problem 2 Three forces meet at a point. Use the graphical technique (vector triangle) to find the resultant vector. In doing so, first complete the sum of Fi and F2 and then complete the sum of F3 and the vector that is (F₁+F2) ● F-35kN, 0₁=115° ● F2-55kN, 02-194° F3-44kN, 03-215° ●

Problem 2 Three forces meet at a point. Use the graphical technique (vector triangle) to find the resultant vector. In doing so, first complete the sum of Fi and F2 and then complete the sum of F3 and the vector that is (F₁+F2) ● F-35kN, 0₁=115° ● F2-55kN, 02-194° F3-44kN, 03-215° ●

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.50P: The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of...

See similar textbooks

Related questions

Q: 12-58. A motorcyclist starting from rest travels along a straight road and for 10 s has an…

Q: Problem 3.9 Solve for the tensile force in cable BA and cable BC that satisfies the conditions of…

Q: 6. The figure below represents a time response of a control system. y() I 0.63 0 What is it? a)…

A: Solution: Given Data: A time response of a control system: To Find:

Q: F1-500 kips 69⁰ 0.8 F3=250 kips 1 + F2 3 concurrent forces are acting on a point as shown. What is…

Q: Q3/0.09m³ of a fluid at 0.7 bar is compressed reversibly to a pressure of 3.5 bar according to law…

Q: In servo motors, the position is determined by: a. The frequency of the PWM signal. b. The amplitude…

A: Servo motors control systems

Q: PROBLEM 2 Determine the force in each member of the truss and state if the members are in tension or…

Q: 7 For pitot-static tube shown below, the flow velocity is equal to: Water L = 0.5 m

A: Given: L = 0.5 cm Required: Velocity of flow

Q: Question 3: A nearly-full cart of water (p=1000 kg/m³) is shown at rest in the figure below. The…

Q: 2. Find the indices for the directions shown in the following hexagonal unit cells. (a) (b)

Q: Determine the force in each member of the loaded truss. All triangles are equilateral with side…

A: Dear Student since you have posted a question with multiple sub-parts, but as per Q& A…

Q: 16) To produce a high head by multistage centrifugal pumps, the impellers are connected: (a) in…

A: Given statement : To produce a high head by multistage centrifugal pump, the impellers are…

Q: 1. Determine the resultant internal loadings acting on the cross-section at C of the simply…

A: As per expert guidelines we are supposed to answer only the first question of the given multiple…

Q: a. By using horizontal element, determine the y-centroid for the shaded area shown in Figure la. Let…

A: Given is the equation of curve and dimensions. Required: Y centroid using horizontal element.

Q: A wind turbine generates power by transferring the kinetic energy of the wind to rotational energy…

A: Given:Wind inlet velocity, V1=7 m/sWind exit velocity, V2=1.75 m/sBlade diameter of wind turbine,…

Q: In a geothermal power plant a underground hot water is available as saturated liquid at 600 kPa. The…

A: Given:P1=529 kPax1=98%P2=15 kPa

Q: E= 29000ksi I=291 in4 6 ft Add your answer B Determine the deflection of the beam at midspan. Answer…

Q: Consider a column of water as it falls from a faucet. The opening in the faucet has radius ro and…

A: Given: faucet with initial velocity v0 and radius r0 To find: (a) velocity expression (b) radius of…

Q: 11. What is not true for the control system stability? d) If a linear, time-invariant system is…

A: To check: Which of the statement is not true for the control system stability. Given: The statement…

Q: Question 3 For the given element: A. 30 MPa 70 5 MPa 15 MPa B a) Determine the normal and shear…

A: The normal stress along the x direction is σx=-15 MPa. The normal stress along the y direction is…

Q: 6 In a flow along a varying flow cross section, as the area decreases: datum head The slope of EGL…

A: Given

Q: 3) Gate AB in the figure is 1.2 m long and 0.8 m into the paper. Compute the force F on the gate and…

A: Given the gate Dimensions. Required- Force on the gate and centre of pressure.

Q: A person is driving along a straight highway at a speed of 21.0 m/s when the traffic light which is…

Q: A 1-58 Willie Lohmann travels from city to city for busi- ness. Every other year he buys a used car…

Q: What would be the likely steps needed to be taken to plan the research, funding, and installation of…

A: As a zero-emission substitute for traditional automobiles, hydrogen fuel cell electric vehicles…

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

Q: Write application software program to find the shortest length of aluminium tubes 50 mm O.D. x 45 mm…

A: Given: The outer diameter of aluminium tube =50 mm The inner diameter of aluminium tube =45 mm The…

Q: The 100 meter diameter wheel needs to be designed so that it rotates at a constant rate and every…

Q: Problem (1.1) Consider a solar-energy- powered ideal Rankine, see figure (1), this cycle uses water…

Q: Q4/ A particular power plant operates with a heat source reservoir at 350 °C and a heat sink…

A: The maximum level of efficiency that a heat engine may achieve is theoretically represented by the…

Q: When the bicycle passes point A, it has a speed of 8 m/s, which is increasing at the rate of v=0.5…

A: Given data:- velocity at point A= 8 m/sAcceleration at point A (horizontal ) = 0.5 m/s2 To find:-the…

Q: In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and…

Q: A flanged bolt coupling has ten 16-mm diameter steel bolts on 800 mm diameter bolt circle a nd six…

A: The given information in the problem is shown in the following attached image:

Q: A V-belt drive is required for a 20 Kw, 1440 rpm electric motor which drives a compressor running at…

A: Given: Power=20 kWN1=1440 rpmN2=480 rpmC0=1.2 m

Q: 4. What is the complement of a 72°21'47" angle?

A: We know that the complement angles pair have sum = 90o let x = 72o 21' 47" (Given) Complement of x…

Q: A 8 ft 20 k B G 80 k 8 ft 8 ft 20 k C 20 k X X X F 80 k 8 ft 8 ft 20 K D E ΠΟΙΟΙΟΙ 8 ft 8 ft

Q: Heat flows through a wall of a house at a steady-state on a day when the temperature of the outdoor…

A: GivenTo=2oC=2+273=275KTi=27oC=27+273=300K

Q: Problem I Suppose the constants a, B and y have the following dimensions: [a]-ML, [B]-ML/T2 and…

Q: Calculate the thermal efficiency of a simple Rankine cycle for which steam leaves the boiler as a…

Q: A block of mass m = 400 g, is attached to a horizontal spring and set in simple harmonic motion as…

A: given: m = 400 g The velocity of the block will be at its maximum at the points where the…

Q: Question 1 A material has a stress of 160MPa [tension X direction] and 120 MPa [compression Y…

Q: The car is traveling at a speed of 30 m/s. The driver then applies the brakes at A and thereby…

Q: 6. Gas turbine engine parts can be successfully inspected only for surface defects by: O Visual…

A: To choose: The correct option: Given: The gas turbine engine parts is successfully inspected only…

Q: A refrigerant system using refrigerant 22 is to have a refrigerating capacity of 60 kW. The…

A: Given:Refrigerant=R22Refrigerating capacity, Q˙e=60 kWEvaporating temperature, Te=-10oCCondensing…

Q: For the acceleration equation, when the term VdV/ds-2 m/s² that means the flow is: In a horizontal 0…

Q: A container is divided into two equal volumes by a very thin membrane. It is held at a fixed…

Q: If FB = 690 N, and Fc = 540 N, determine the magnitude of the resultant force acting on the flag…

A: According to the given data FB=690N Fc=540N we need to find The resultant of the forces using data…

Q: CONSIDER A 210-MW STEAM POWER PLANT THAT OPERATES ON A SIMPLE IDEAL RANKINE CYCLE. STEAM ENTERS THE…

Q: 2) The specific weight of a fluid is 20000 N/m³. The pressure (above atmosphere) in a tank bottom…

A: Q-2 Given data Specific weight = 20000(N/m3) The height = 0.2m Find the pressure in the tank bottom

Q: 2.62 For W = 800 N, P = 200 N, and d = 600 mm, determine the value of h consistent with equilibrium.

Question

Problem 2
Three forces meet at a point. Use the graphical technique (vector triangle) to find the resultant
vector. In doing so, first complete the sum of Fi and F2 and then complete the sum of F3 and the
vector that is (F₁+F2)
● F-35kN, 0₁=115°
● F2-55kN, 02-194°
● F3-44kN, 03-215°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the forces Q1,Q2, and Q3 so that the two forces systems are equivalent.
The three forces of magnitude P can be replaced by a single, equivalent force R acting at point A. Determine the distance x and the magnitude and direction of R.
The two forces are applied to the end of the boom OA. Determine the force F so that the resultant of the two forces lies in the yz-plane.
The tensions in the cables supporting the pole are T1=T2=T3=60kN. Replace the cable tensions with an equivalent force-couple system with the force acting at O. Express your answer in vector form.
The pole OB is subjected to the 6004b force at B. Determine (a) the rectangular components of the force; and (b) the angles between the force vector and the coordinate axes.
When the three forces are replaced by an equivalent force-couple system with the force at point O, the couple vector CR is directed parallel to the x-axis. Determine F and the resultant force-couple system.
Determine the resultant force or resultant couple for each of the line loads shown. In each case the loading is normal to the line and has constant intensity w0.
Find the internal force systems acting on sections 1 and 2.
Three professional wrestlers are fighting over a champion’s belt, and each exerts a force on the belt. Wrestler 1 exerts a force F1 = 40.0 N in the +x-direction, wrestler 2 exerts a force F2 = 80.0 N in the -y-direction, and wrestler 3 exerts a force F3 = 60.0 N at an angle of 36.9° counterclockwise from the +x-direction. Find the xand y-components of the net external force on the belt, and find the force’s magnitude and direction.