Problem 21: A rod is composed of three segments and carries the axial loads as shown. Determine the stress in each material Indicate if C or T. The properties of each segment are given below. Bronze 120 KN 50 kN Aluminum Steel Bronze Aluminum Steel 1 (mm) A (mm²) E (GPa) 600 2400 83 400 1200 70 300 600 200

Problem 21: A rod is composed of three segments and carries the axial loads as shown. Determine the stress in each material Indicate if C or T. The properties of each segment are given below. Bronze 120 KN 50 kN Aluminum Steel Bronze Aluminum Steel 1 (mm) A (mm²) E (GPa) 600 2400 83 400 1200 70 300 600 200

Residential Construction Academy: House Wiring (MindTap Course List)

5th Edition

ISBN:9781337402415

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter4: Test And Measurement Instruments Used In Residential Wiring

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
ngr. Beleric measured a distance line using a 20m length of stainless steel tape measure. The line's length was determined to be 396.84meters.The temperature was 10 oC during the measurement, and the tape was supported on both ends.The tape has a cross sectional area of 7.20mm2 and a modulus of elasticity of 200GPa. The tape is 0.095 kg/m in weight. k = 11.6 x10-6 m/C If the engineer determined the lengths of the Temperature correction, Pull correction, and Sag Correction to be 1,197.23μm, 285.53 μm, and 2.23 mm, per segment, Calculate the 20m tape's standard pull in kilograms.
A wide flange A60 steel column has a length of 6.4meters and pinned ends. If Sx=888x103 mm3, Sy=128x103 mm3, d=358mm, bf=184mm, A=7,289mm2, Fy=414MPa, calculate the critical buckling stress, Fcr in MPa of the column. Express your answer in one decimal place.
A steel plate 375mm x 16mm thick is bolted by four bolts placed symmetrically to form a single lap joint. The bolts are spaced horizontally at a distance of 140mm and vertically at a distance of 150mm. If the diameter of bolt is 20 mm, calculate the design tensile strength in KN based on net section fracture considering a straight vertical path of failure Use Fy=248MPa and Fu=400MPa a) 1339.2 b) 1569.6 c)2092.8 d) 1488
From the bracket connection shown. 1. Which of the following gives the stress due to axial load. a. 62.07 MPa b. 75.56 MPa c. 52.89 MPa d. 19.34 MPa 2. What is the value of ‘b’ that will make the maximum stress due to moment equal to that due to axial load? a. 150 mm b. 200 mm c. 250 mm d. 300 mm 3. What is the eccentricity? a. 300 mm b. 250 mm c. 150 mm d. 196.78 MPa
A rigid block is supported by three symmetrically spaced rods as shown. Two are made of steel and one is made of brass. Each rod has a cross sectional area of 8-in2. The block weighs 80,000-lb and all three post have the same length before loading. Solve for the normal stress experienced by each post when the brass rod is heated until the temperature increases by 20°F. Use: Esteel=29*103-ksi, Ebrass = 14.6*103-ksi αbrass = 9.8*10-6/°F.
Question 16 A W10x30, 2.9 m long, A36 steel is used as a column with fixed ends to support a service dead load of 154 kN. Calculate the maximum service live load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN. A = 5,703 mm2 rx = 111.25 mm ry = 34.80 mm
Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on each bolt (MPa)
Two solid steel shafts (shafts) in the figureconnected with gears. Permission for steel shaftsthe permissible shear stress is 7000 psi. BC spindle1.6 in diameter and 1.25 in diameter of EF shaftit is known that the width applied to the shaft at the C pointCalculate the large TC torque.
The adjacent sketch indicates a brass wire which is exactly 12.00 m long and a steel wire which is 12.01 m long. Each wire has a cross-sectional area of 150 mm2 . What load does each wire carry if E steel = 200,000 MPa & E brass = 110,000 MPa? (Hint: no load on steel wire until brass wire stretches by 10mm, then ratio of stresses in each wire is same as ratio of E v
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
a. Calculate "P" in KN considering tension failure on gross area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm