Problem #3 (5 points): A mechanical system is subjected to normal and shear forces that cause normal strain of 0.002 (mm/mm) and shear strain of 0.001 rad. If the normal stress is 250 MPa and the Poisson's ratio is 0.3. determine the shear stress.

Problem #3 (5 points): A mechanical system is subjected to normal and shear forces that cause normal strain of 0.002 (mm/mm) and shear strain of 0.001 rad. If the normal stress is 250 MPa and the Poisson's ratio is 0.3. determine the shear stress.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.12P: Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in...

See similar textbooks

Related questions

Q: A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine…

A: Given The outside diameter of hollow steel tube is D=138 mm. The inside diameter of tube is d=120…

Q: 3.For a body under three dimensional stress state, describe the procedure for obtaining the absolute…

A: Derive the equation for absolute maximum and stress using Mohr circle

Q: In the wood industries, inclined blocks of wood are sometimes used to determine the…

Q: A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of…

Q: a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a…

A: Given Tensile load, P =3 kN Cross-section = 4mm X 4mm Find The applied engineering…

Q: A 20 in. long work piece with a cross sectional area of 2 in? (see the accompanying figure) is…

Q: Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and…

Q: The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress of…

Q: Write out the most general expression for tension orcompression strain along a single axis resulting…

A: The Strain is defined as the ratio of the change in dimension to the initial dimension of the object…

Q: A specimen of aluminum having a rectangular cross section 10 mm x 12.7 mm is pulled in tension with…

Q: Define the term maximum in-plane shear stress?

A: Consider the diagram shown below for the principal stresses at a point.

Q: Problem Solving: Show your Solution 1. A sculpture weighing 10,000 N rests on a horizontal surface…

A: 1) Weight of sculpture =10000 N h=6 m A=0.20 m2 density =2700 kg/m3 length of segment =3 m

Q: When can the shear stress be determined from the torsion formula?

A: Let a solid circular shaft fixed at one end is applied with an external torque. There will be…

Q: What is the stresses in the rail at 50°C , if there is an expansion allowance of 5 mm per rail .

A: Given data: The temperature of the rail is Tf = 50oC. The expansion allowance is l = 5 mm.

Q: In the nominal stress-strain diagram (Figure 1), write down the names and meanings of points 1, 2,…

A: Point 1 is the ultimate stress at which the material can sustain. After this point the fracture of…

Q: Besides normal tensile stress, list three other types of material stresses? Are these typically all…

A: Stress: Stress is defined as the internal resistance per unit area of cross-section. There are…

Q: A box- shaped piece of Delon shampoo has a top area of 17 cm2 and a height of 5.0 cm. when a…

A: The area of the box shaped shampoo is, (A)=17 cm2. The height of box is,(L)=5.0cm. The upper surface…

Q: The offset yield strength is obtained by drawing a parallel line from_______________of strain.

Q: A 0.1-in wire that is 10-in long and supports a 100-lb weight stretches a total of 0.1-in. What is…

A: Given question belongs to the subject Strength of materials and can be solved using the concepts of…

Q: A 6 mm thick plate is to be punched of a shape shown in figure. Determine the minimum punching force…

Q: Two strip of metal are pinned to gather as shown in fig below with a rod of 10 mm diameter. The…

A: Given Information: The diameter of the rod (d) = 10 mm The ultimate shear stress of the rod (S) = 60…

Q: 2) The strength coefficient and strain-hardening exponent of a certain test metal are 750 MPa and…

Q: Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in…

A: Given DataE1=74 GPaA=1749 mm2L=738 mmE2=204 GPa

Q: The is a graphical representation of fatigue strength on the Y-axis and the number of stress cycles…

Q: 1) For a certain metal, the strength coefficient= 700 MPa. A tensile specimen of the metal with gage…

A: Given: Strength coefficient (k)=700MPaGauge length (L)=150mmStretched length (L0)=207mm

Q: For a certain metal, the strength coefficient= 700 MPa. A tensile specimen of the metal with gage…

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 200 mm.…

A: since you haven't mentioned the value of poison ration and elastic modulus that's why the reference…

Q: A 1.25 inch diameter hole is drilled on the centerline of a steel bar 3.5 inches wide by 3/8 inches…

Q: A rectangular block of material is subjected to a tensile stress of 90 N/mm2 along X axis and a…

A: Given data: - The tensile stress on the block is σx = 90 N/mm2. The compressive stress on the block…

Q: In the course of Material Mechanics, you may study that for the bar under tensile loading, the…

Q: Define plane stress and plane strain, making clear which, if any, of the stresses are zero in each…

A: Plane stress If a plane is undergoing load and at any point, the normal stress vector is zero (the…

Q: In a sheet metal of 2 mm thickness a hole of 10 mm diameter needs to be punched. The yield strength…

A: Given that metal thickness = 2 mm Hole diameter is 10 mm And the ultimate shear is 80 MPa.

Q: A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z…

A: Given Force. FX = 250 kN FY = 320 kN FZ = 180 kN Find Strain in X…

Q: A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and…

Q: Example 136.A cylindrical pressure vessel is fabricated from steel plating that has a thickness of…

Q: In a sheet metal of 2 mm thickness, a hole of 10 mm diame- ter needs to be punched. The yield…

Q: After the yield region in the stress-strain curve the strength up to ultimate value because:

A: When the stress is applied slip planes start to move in the direction of applied stress. Millions of…

Q: A double riveted lap joint is made between 15mm thick plates. The rivet diameter and pitch are 25 mm…

Q: Derive the following equation for computing shear stress in a solid bar along an oblique plane with…

Q: block of rubber 500 mm long, 20 mm wide and 400 mm high has its lower face fixed and its upper face…

Q: The strength coefficient and strain-hardening exponent of a certain test metal are 750 MPa and…

A: We need to calculate the final diameter of the specimen

Q: نقطتان )E A tensile test is performed on a metal specimen, and it is found that a true plastic…

A: Given: True stress σ1=500MPaTrue strain ε1=0.16Strength coefficient (K)=825MPa Solution: True stress…

Q: Calculate the principle stresses and the maximum shear stress.

A: Given: σx =10 Psi T σy = 25 Psi T τ = 5 Psi

Q: True stress-strain Engineering stress-strain strain Calculate the engineering ultimate tensile…

Question

Problem #3 (5 points): A mechanical system is subjected to normal and shear forces that cause normal strain of
0.002 (mm/mm) and shear strain of 0.001 rad. If the normal stress is 250 MPa and the Poisson's ratio is 0.3,
determine the shear stress.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
If the shear stress in a material is 20 MPa and the corresponding shear strain is 0.0005, calculate the shear modulus of the material.
In a sheet metal of 2 mm thickness a hole of 10 mm diameter needs to be punched. The yield strength in tension of the sheet material is 100 Mpa and its ultimate shear strength is 80 MPa. Determine the force required to punch the hole.
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains.
Write out the most general expression for shear strain along a single axis resulting from all possible applied stresses, assuming that the material is elastically isotropic.
Hexagonal nuts for 6.25mm diameter bolts have a height of 5.5mm. If the ultimate strength of the nut material in shear is 103MPa, what is the most nearly the maximum allowable shear force on the nut thread using a safety factor of 5?
With the force P appliced on a member, the stress distributions at different cross sections are different as shown below. However, at locations far enough away from the support and the applied load, the stress distribution becomes uniform. This is due to: Inelastic property Poisson’s effect Saint Venant’s Principle Principle of superposition
Question 1: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the maximum axial force (P) that can be applied. d=100mma) On the theory of maximum normal stressb) Maximum shear stress theoryc) Calculate according to the maximum strain energy theory.The structure is made of steel and the proportional limit is 250 MN / m2 in pressing and drawing, and 140 MN / m2 in shear. The elasticity module of the material is 200 GPa and the Poisson's ratio is 0.3. d=100mm
A punch for making holes in steel plates is shown in Figure 4. Assume that a punchhaving diameter d = 20 mm is used to punch a hole of 8 mm plate. If force, V = 110kN is required to create the hole, determine the shear stress in the plate.
Define different types of stresses, strains and material constants. Also solve 4 numerical problems on stresses and strains for multiaxial loading conditions.