Answer parts a and b. Problem 3: An RC low-pass filter is shown in the figure. Its purpose is to attenuate higherfrequencies while allowing lower frequencies to pass through. A 820-Hz sine-wave signal with rmsamplitude of Vms = 1.4 V is fed into the filter. The values of the components are R = 140 Q and C =0.66 µF.OutRrmsPart (a) Find the output rms voltage, in volts.Vout-rms = 1.2639Vout-ms = 1.264Part (b) By what angle, in degrees, does the output voltage lag the input voltage?sin()cos()tan()7HOMEcotan()asin()acos()E46atan()acotan()sinh()123cosh()ODegrees O Radianstanh()cotanh()+ENDvol BACKSPACEDEL CLEAR

Answered: Image /qna-images/answer/3a46d887-a64b-4f7a-b01c-31f94cf05c0c.jpg

Problem 3: An RC low-pass filter is shown in the figure. Its purpose is to attenuate higher frequencies while allowing lower frequencies to pass through. A 820-Hz sine-wave signal with rms amplitude of Vms = 1.4 V is fed into the filter. The values of the components are R= 140 Q and C = Out R 0.66 µF. rms Part (a) Find the output rms voltage, in volts. Vout-rms = 1.2639 Vout-rms - 1.264 v Part (b) By what angle, in degrees, does the output voltage lag the input voltage? sin() cos() tan() 7 8 9 НОМЕ asin() acotan() cotan() acos() E 4 6 atan() sinh() 1 tanh() cosh() ODegrees O Radians cotanh() END BACKSPACE CLEAR

Problem 3: An RC low-pass filter is shown in the figure. Its purpose is to attenuate higher frequencies while allowing lower frequencies to pass through. A 820-Hz sine-wave signal with rms amplitude of Vms = 1.4 V is fed into the filter. The values of the components are R= 140 Q and C = Out R 0.66 µF. rms Part (a) Find the output rms voltage, in volts. Vout-rms = 1.2639 Vout-rms - 1.264 v Part (b) By what angle, in degrees, does the output voltage lag the input voltage? sin() cos() tan() 7 8 9 НОМЕ asin() acotan() cotan() acos() E 4 6 atan() sinh() 1 tanh() cosh() ODegrees O Radians cotanh() END BACKSPACE CLEAR

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter33: Alternating Current Circuits

Section: Chapter Questions

Problem 33.53P: The RC high-pass filter shown in Figure P33.53 has a resistance R = 0.500 and a capacitance C = 613...

See similar textbooks

Similar questions

For an RLC series circuit, the voltage amplitude and frequency of the source are 100 V and 500 Hz, respectively; R=500 ; and L = 0.20H . Find the average power dissipated in the resistor for the following values for the capacitance: (a) C=2.0F and (b) C=2.0F .
What is the impedance of a series combination of a 50resistor, a 5.0F capacitor, and a 10F capacitor at a frequency of 2.0 kHz?
A 1.5k resistor and 30-mH inductor are connected in series, as below, across a120-V(rms)ac power source oscillating at 60-Hz frequency. (a) Find the current in the circuit. (b) Find the voltage drops across the resistor and inductor. (C) Find the impedance of the circuit. (d) Find the power dissipated in the resistor. (e) Find the power dissipated in the inductor. (1) Find the power produced by the source.
A 20-mH inductor is connected across an AC source with a variable frequency and a constant-voltage amplitude of 9.0 V. (a) Determine the reactance of the circuit and the maximum current through the inductor when the frequency Is set at 20 kHz. (b) Do the same calculations for a frequency of 60 Hz.
A 700-pF capacitor is connected across an ac source with a voltage amplitude of 160 V and a frequency of 20 kHz. (a) Determine the capacitive reactance of the capacitor and the amplitude of the output current of the source. (b) If the frequency is changed to 60 Hz while keeping the voltage amplitude at 160 V, what are the capacitive reactance and the current amplitude?
In the AC circuit shown in Figure P32.3, R = 70.0 and the output voltage of the AC source is Vmax sin t. (a) If VR = 0.250 Vmax for the first time at t = 0.0100 s, what is the angular frequency of the source? (b) What is the next value of t for which VR = 0.250 Vmax? Figure P32.6 Problem 3 and 5.
Calculate the reactance of a 5.0F capacitor at (a) 60 Hz, (b) 600 Hz, and (c) 6000 Hz.
The emf of an ac source is given by v(t)=v0sint. where V0=100V and at =200rad/s . Calculate the average power output of the source if it is connected across (a) a 20F capacitor, (b) a 20-mH inductor, and (c) a 50 resistor.
The RC high-pass filter shown in Figure P33.53 has a resistance R = 0.500 and a capacitance C = 613 F. What is the ratio of the amplitude of the output voltage to that of the input voltage for this filter for a source frequency of 600 Hz?
A series RLC circuit has resistance R = 50.0 and inductance L. = 0.500 H. (a) Find the circuits capacitance C if the voltage source operates at a frequency of f = 60.0 Hz and the impedance is Z = R = 50.0 . (b) What is the phase angle between the current and the voltage?