Problem #3: The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft ( D = 2.25” and d = 0.90” ). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12 x 106 psi, 4 x 106 psi, and 6 x 106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft. A 0.90 in Steel 7.5 ft 254 lb-ft Aluminum 2.25 in 512 lb-ft Bronze 0.90 in D 5 ft 3.75 ft- B

Problem #3: The compound shaft consists of solid steel and bronze shafts and hollow aluminum shaft ( D = 2.25” and d = 0.90” ). It is subjected to two torques as shown in the figure. The moduli of rigidity for steel, aluminum, and bronze are 12 x 106 psi, 4 x 106 psi, and 6 x 106 psi, respectively. Determine the shearing stress developed in each material. Also, calculate the angle of twist incurred by the aluminum shaft. A 0.90 in Steel 7.5 ft 254 lb-ft Aluminum 2.25 in 512 lb-ft Bronze 0.90 in D 5 ft 3.75 ft- B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow steel (E= 30,000ksi) tube (1) with an outside diameter of 2.75in. and a wall thickness of 0.25in. is fastened to a solid aluminum (E= 10,000 ksi) rod (2) that has a 2in. diameter and a solid 1.375in. diameter aluminum rod (3). The bar is loaded as shown in the figure. Determine (a) the change in length of steel tube (1); (b) the deflection of joint D with respect to the fixed support A. (c) the maximum normal stress in the entire axial assembly.
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
A SOLID ALUMINUM SHAFT 2 INCH DIAMETER IS SUBJECTED TO TWO TORQUES AS SHOWN IN THE FIGURE. DETERMINE THE MAXIMUM SHEARING STRESS IN EACH SEGMENT AND THE AGLE OF ROTATION OF THE FREE END, USE G = 4 X 106 PSI.
A solid 1.40-in.-diameter steel [G = 12,000 ksi] shaft is subjected to the torques shown. Determine the magnitude of the maximum shear stress in shaft segment (1). a 1.82 ksi b 2.45 ksi c 3.86 ksi d 3.01 ksi e 2.85 ksi
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
For the beam shown, determine the support reactions and draw the stress diagrams. shear and bending moment. EI is constant. The rigth answer is: VA = 1.3 kN (↑); HA = 0 kN; MA = 4.40 kN.m (clockwise); VB = 51.20 kN (↑). I don't know how to get these results, please show how, step by step.
The following rigid structure ABCD is supported by a hinge at B and two bars at C and D. The applied load is 100 kN. The data is shown in the table. Determine: The stress in each bar. Answ: 27.01 MPa, 328.01 MPa The vertical displacement at the point where the load is applied. Answ: 0.9403 mm. The rotation at point B. Answ: 0.001069 rad. The horizontal displacement 400 mm below point B. Answ: 0.42741 mm.
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
3) Solve the following problem: The hollow tube ABCDE is made of a material that is subjected to five torsores that act as shown in the figure below. The outside diameter of the tube is d2 = 1.0 inches. The maximum allowable shear stress is 12,000 psi (12,000 lb / inch ^ 2). In addition, the maximum rotation per foot allowed is 2.0 degrees (2.0 degrees / foot). Take G = 9500 Ksi (9,500,000 psi). Note: Remember that 1 degree equals 0.0175 radians. Determine the maximum internal diameter d1, allowed for the tube.
Given the state of stress shown, determine the normal stress (in MPa) acting on the inclined plane a-a if S = 93.19 MPa, N = 42.03 MPa, and A = 36.4°. Express final answer in four decimal places.
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P=55)