Problem 4-33: The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. Determine the average normal stress in the aluminum and the steel due to this loading. The pipe has an outer diameter of 400 mm- 80 mm and an inner diameter of 70 mm. 200 kN 200 kN

Problem 4-33: The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. Determine the average normal stress in the aluminum and the steel due to this loading. The pipe has an outer diameter of 400 mm- 80 mm and an inner diameter of 70 mm. 200 kN 200 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Related questions

Q: Obtain a state-space representation of the mechanical system shown below, where u₁ and u₂ are the…

Q: Apply Denavit-Hartenberg rules to draw the frames on the kinematic diagram of the following…

A: DefinitionDenavit-Hartenberg:Denavit-Hartenberg is a convention for linking reference frames to the…

Q: Zirconium has an HCP crystal structure and a density of 6.51 g/cm³. (a) What is the volume of its…

A: The density of a substance related to crystal volume is as below,

Q: Give the total gear ratio and the ratio required in the gear box. State any assumptions and give…

A: DefinitionGear ratio:A gear ratio is the ratio of the rotational speeds or torques of two inter…

Q: 60 kN/m Z 60 kN/m 60 kN/m 60 kN/m Consider the spring assemblage shown in the figure above. Use the…

A: The force applied at node 3 is

Q: What is the peak voltage of an AC circuit which has an RMS voltage of 115V?

A: RMS value: The effective or equivalent DC (direct current) of the RMS value represents the value of…

Q: Find p¹ and matrix R₂.

A: The preceding method entails applying linear algebra techniques to the issue of determining the…

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the x-axis (θx)? Note that…

Q: Determine the magnitude of the force F(in KM) so the resultant couple moment is 20 kN.m clockwise.…

A: From trigonometry relationship,

Q: fimm. For the spring assemblage shown in the figure above, determine the displacement at node 2 and…

A: The value of spring constant is The displacement of node 3 is

Q: The composite wall of an oven consists of three materials, two of which are of known thermal…

Q: Part C What is the angular frequency w of oscillations of the rod? Express the angular frequency in…

Q: A 10-kg steel sphere is suspended from the 15-kg frame which slides down the 20° incline. If the…

Q: A special sensor is designed to sense the percent vapor present in a liquid vapor mixture. If during…

A: Find out the sensitivity of the sensor.

Q: Determine the force in each cord for equilibrium of the 60-kg bucket. Complete solutions must…

A: For the solution refer below images.

Q: One solution is to cool the exhaust stream, which requires energy and equipment. To recover 35% of…

A: The approach shown below entails analyzing and designing a system capable of recovering heptane from…

Q: 10 b 15 in. 15 in. poccor D 30° 10 b TO P

A: To findWhat is the minimum tension P of the cord?What is the orientation, ?Given the resultant…

Q: Draw the Mohr circle of inertia moments and show how to find Imin and Imax

A: By using a circle and its properties to determine an area's principal moments by plotting the…

Q: If there are three gears A, B, C number of teeth in A is 32, B is 45, and C is 48. B is the idler…

Q: For the Scalar projection of F along r = F * Ur How did you get the -41.924 + 24.0327

A: We have following data:Force vector is, Unit vector in the direction of vector r is,

Q: For the mechanism shown below, use the graphical position analysis to specify the value(s) of 02…

A: Link 3 will be tangent to the circle with center O2 when link 6's linear speed is zero. Two tangents…

Q: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

A: What are the tensions in each of the 4 cables supporting the lamp, if the lamp weighs 50 lbs and the…

Q: The spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless…

A: The objective of this problem is to find the component of the reaction at A in a direction…

Q: Solution: FA 147.15 N, FB = 254.87 N = 60° 30 kg B 30°

A: Given:The mass of the barrel,

Q: For 6.5 s, a rocket rises along a rectilinear trajectory oriented at 70 degrees relative to the…

Q: To Determine Angunar veuocity of Arm velocity at Point C

A: Given:Velocity at A = 14mm/sAB = 25 cmBC = 15 cmTo find:Angular velocity at armVelocity at point…

Q: Pulleys A and B are mounted on bracket CDEF. The tension on each side of the two belts is given as…

A: A pulley systemTo find Line of interaction

Q: 6. An old automobile exhibits a vertical oscillating displacement of maximum amplitude 7 cm and an…

A: For the solution refer below images.

Q: The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate…

A: DefinitionS-N Diagram:The S-N diagram can be used to design components that are subject to cycle…

Q: k= 5000 lb/in. k= 5000 lb/in. k= 5000 lb/in. 1000 lb U2 = بس = Consider the spring assemblage shown…

A: The value of force is

Q: 320 mm 380 mm C 220 mm 960 mm 900 mm 240 mm PROBLEM 2.92 Three cables are connected at A, where the…

A: Three cables are connected at A, where the forces P and Q are applied as shown. Knowing that…

Q: (b) (c) Calculate the hoop tension, Fe due to centrifugal force. b Find the torque, T due to the…

A: DefinitionHoop tension:Hoop tension, also known as hoop stress, is the stress that develops in the…

Q: Task 2.1: In a horizontal water pipe (length L=10 m) inner radius r; = 1.25 cm), water flows with an…

A: Given:The length of the pipe, The inner radius of the pipe, The diameter of the pipe, The inlet…

Q: • . isentoopie efficiency of the turbine = 861. isentropic"," of pump = 91% • If Dolynesi traction…

A: To findDetermine the thermal efficiency of the plant.GivenIsentropic efficiency of the turbine =…

Q: A thermostat adjusting mechanism capillary tube sensing bulb A 3D printer head moving mechanism…

A: The thermostat adjusting mechanism can be categorized as a function generation case. In this…

Q: The container truck engine operated on the diesel cycle with a compression ratio of 12. Assume the…

A: “Since you have posted a question with multiple subparts, we will provide the solution only to the…

Q: Determine the crystallographic direction for vector AB shown in the figure below: ANSWERS: answer as…

Q: SAE 10W-30 oil with viscosity 1 x 10-4 lbf s/ft2 is used as a lubricant between two parts of a…

Q: The pictured member has lengths L₁ = 6 ft, L₂= 3 ft, and L3 = 6 ft, with the applied forces at A of…

A: Forces acting at point A are given below: are unit vectors along axes respectively.It is required…

Q: The beam shown below carries point and linearly distributed loads and is supported by a pin on the…

Q: If the direction cosines for the satellite antenna shown are to be cosex = 0.286, cosły= 0.429, and…

A: The direction cosine of antena are

Q: A composite plane wall consists of a 5-in.-thick layer of insulation (k, = 0.029 Btu/h ft R) and a…

A: It is given that:It is required to determine:(a) Temperature at the interface of the two layers.(b)…

Q: A point in a brittle material of ultimate strength equal to 600 MPa has the following state of…

A: GIVEN:We know that ------- (1)Now, find maximum principle stress by using Formulas

Q: 3.21 Some animals have learned to take advantage of the Bernoulli effect without having read a fluid…

Q: Using Hardy-Cross + Darcy- Weisbach analysis, one of 4 rectangular pipe network has kvalue of…

A: Value of k=58.9584Flow rate:And it is a four rectangular pipe network:

Q: The 1 inch diameter shaft is subjected to the loads shown. Draw the "loading diagram" showing the…

A: To findDraw the loading diagram showing the internal forces and moment/Torque acting on a cut…

Q: a mass-spring-damper system has a mass of 100 kg. In 60 s, its free response apmplitude decays such…

A: The mass is The total time to decay is The amplitude of 30th cycle is of the 1st cycle

Q: explain in detail how you got all the Md, Ma, Mc,Mb answers and vice verca withe the Vb, Va, Vc,…

A: The shear and moment equation of EA section is The shear and moment equation of AD section is The…

Q: 3.32 WP Water, initially saturated vapor at 4 bar, fills a closed, rigid container. The water is…

A: Initial state: saturated vaporFinal state:Since container is rigid and closed, hence its volume…

Q: Two 4.5-\mu F capacitors, two 2.5 k\Omega resistors, and a 20.0 - V source are connected in series.…

A: Capacitance of the capacitor C = 4.5 x10-6 FResistor connected in series with the capacitor R = 2…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

5 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.

Problem 4-33:
The A-36 steel pipe has a 6061-T6 aluminum core. It is subjected to a tensile force of
200 kN. Determine the average normal stress in the aluminum and the steel due to this
loading. The pipe has an outer diameter of
-400 mm-
80 mm and an inner diameter of 70 mm.
200 kN
200 KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: To determine :The average normal stress in the aluminum and the steel

VIEW

Step 2: The average normal stress is,

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
Topic: MACHINE DESIGN A submersible cylinder used in research has a cylindrical pressure hull of outside diameter 3.0 m and a wall thickness of 150 mm. It is constructed of an aluminum alloy, having a yield point of 450 MPa. Determine the tangential stress, in terms of MPa, in the cylindrical portion of the pressure hull whenthe vehicle is at its operating depth of 5500 m below the surface of the sea. Consider sea water to have a specific weight of 104 N/m3
a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly c) The shear stress in the pin at C is most nearly
If the A-36 solid steel rod has a diameter of 50 mm and has been loaded with loadings as shown in Figure Q4, determine the state of stress at point A and B and subsequently sketch their stress elements.
The d = 17-mm-diameter solid rod passes through a D = 22-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 10 mm. The rod head has a diameter of a = 34 mm, and the head has a thickness of t = 8 mm. The shear stress in the rod head cannot exceed 145 MPa, the punching shear stress in the support plate cannot exceed 100 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure.
A spherical pressure vessel has an outer diameter of 75 mm and a wall thickness of 10 mm. It's made of a steel having the yield strength (Sy) of 300 MPa. If the largest principal normal stress is not to exceed 80% of the yield strength, determine the maximum internal pressure this pressure vessel can withstand. The pressure vessel is considered thick-walled spherical pressure vessel.
A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
A safety valve spring made of oil-tempered chrome vanadium steel having a 9.5 coils has squared and ground ends. The outside diameter is 115 mm and wire diameter is 13 mm. It has a free length of 203 mm. The spring must be initially compressed to hold the boiler pressure of 1.38 Mpa on the valve seat of 32 mm diameter. Determine the spring stress if it is compressed to its solid length.
4. The compression load of 120 kN acts on the steel pipe of Table B-14. Determine the minimum Nominal dimeter pipe when the safety factor is 1.5 with a yield strength of 240MPa.
1) The cylinder for a hydraulic press has an insidediameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of (60 + 20) MPa.