Answered: The cylinder for a hydraulic press has…

The cylinder for a hydraulic press has an insidediameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of (60 + 20) MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.14P: The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind...

See similar textbooks

Related questions

Q: The solid shaft is fixed in the wall at A (Figure Q2). A force F is applied at B, determine a) the…

Q: A flanged bolt coupling consists of ten 20-mm diameter steel bolts spaced evenly around a bolt…

Q: A steel punch consists of two shafts: uppershaft and lower shaft. Assume that the upper shafthas a…

A: The shearing stress in the plate can be calculated using the formula given below as- τ=Pπdt where, P…

Q: A mild steel shaft transmits ‘P’ kW at ‘N’ r.p.m. It carries a central load of 900 N and is simply…

A: Given data, Central load W= 900 N allowable shear stress = 42 MPa The maximum tensile or…

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

Q: 2 m hollow cast iron pole has an outside diameter of 250 mm and a thickness of 10 mm. The pole is…

A: Given Data P=15 kN D=250 mm t=10 mm

Q: A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the…

A: Given Data⇒ Line shaft rotating at (N)=320 rpm Power transmitted (P)=35 KW Allowable shear stress…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner radiu…

Q: A hydraulic punch press is used to punch a slot in a 0.50-in.-thick plate, as illustrated in Figure.…

Q: Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the…

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…

A: Inside diameter = 300 mm Inside radius = 150 mm outside radius = 260 mm internal pressure = 80 Mpa

Q: Complete answer

A: Given Data: Diameter of OB and AB (D) = 100 mm = 0.1 m Radius of disc (r) = 0.5 m Allowable normal…

Q: A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the…

A: GIVEN :- E = 214Gpa G= 83Gpa σy=15 MPaσx=-30 Mpaζxy=25 MPa

Q: A state of stress is specified in the figure shown below. Determine the Normal stress ox (mPa) on…

Q: Q3. For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…

A: given data inner radius = 20 mm outer radius = 40 mm internal pressure = 5 Mpa

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

A: Given data: The diameter of the part AB is dAB=15 mm The diameter of the part BC is dBC=18 mm The…

Q: Each of the four links in Figure has an 8x36mm uniform rectangular cross section and each of the…

A: Consider the free body diagram as shown below for the link ABC. From the moment equilibrium about…

Q: 2. A plane element in a body is subjected to a compressive stress of 80 MPa accompanied by a shear…

Q: The stepped steel shaft carries the torque T. Determine the allowable magnitude of T if the working…

A: Answer: The magnitude of allowable torque is 933.0530 N•m.

Q: 3. An element in a strained body is subjected to a tensile stress of 100 MPa and a shear stress of…

A: When an amount of force act on an object, then the force has the tendency to change the shape of the…

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the…

A: As per given question If the allowable normal stress is 120MPa and the allowable shear stress is…

Q: Problem No. 3. The compound shaft has the following properties: G in both Segment 1 Segment 1 pipe…

Q: 1- The principal stresses or a point in the section of a member are 50 MPa or 20 MPa both tensile.…

A: To find : The normal and shear stress. Given : The principal stresses are σ1=50 MPa. σ2=20 MPa.…

Q: (a): The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of…

A: a) Given: The cylinder for a hydraulic press,*inside diameter d=300mm*outside radius…

Q: 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If…

A: P= Stress x Arivets P=80[1/4 π (202)] P=8000 π N From bearing of plate material:P=σbAb 8000 π = 140…

Q: A spring was made by a steel wire of 25 mm diameter around a 175 mm diameter cylinder. determine the…

Q: A block is subjected to a compressive force of 2kN. Determine the shear stress and the normal stress…

Q: The torque shown in the figure is exerted on pulleys A, B and C. If it is known that the AB axis is…

Q: 4- A hollow tubular shaft is 1.5 m long and has an outer diameter of 75-mm. The shaft transmits the…

Q: An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a…

Q: In figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm…

Q: A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the…

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…

A: Given data, Internal diameter of the hydraulic cylinder, Di = 300 mm Outer radius of the cylinder,…

Q: The 12 kN.m torque is applied to the free end of the 5-m steel shaft. The angle of rotation of the…

Q: The Mohr's circle for a point near the base of a traffic pole is shown below. the center of the…

A: Consider the diagram shown below for the given Mohr’s circle.

Q: 4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure…

Q: Observe the figure below. Determine the following: a. axial stress on the shank if the load applied…

Q: 2- The normal stress in an inclined plane is 21.782 Mpa, the stress in the x-axis is 35 Mpa, in the…

Q: If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B…

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm.…

Q: The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260…

A: The pressure difference between the inner and outer surfaces of a cylinder applies stress on the…

Q: 3-m long thin-walled tube has an equilateral triangular cross-section with a constant thickness of…

Q: The state of stress acting at a critical point on a wrench is shown in the figure. Determine the…

A: Given: The state of stress is given as Here, σx=300 MPaτxy=150 MPa

Q: GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane…

Q: 3. A cylinder with one closed end and one free end has an outer radius, b =260mm, and an inner…

A: solutionwe have given in the question.outer radius (r0)=260mminner radius (ri)=55mminterval pressure…

Q: 1. A shaft 80 mm diameter transmits power at maximum shear stress of 63 MPa. Find the length of a 20…

A: as per guideline i have to solve only first question

Q: 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given…

Q: A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the…

A: GivenThickness pf the plate t=0.60inshear stress τ=31ksid=0.5ina=2.75in

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

The cylinder for a hydraulic press has an insidediameter of 300 mm and an outside radius

of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of

(60 + 20) MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
An aluminum pole for a street light weighs 4600 N and supports an arm that weighs 660 N (see figure). The center of gravity of the arm is 1.2 m from the axis of the pole, A wind force of 300 N also acts in the (y) direction at 9 m above the base. The outside diameter of the pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressive stresses o, and e1., respectively, in the pole (at its base) due to the weights and the wind force.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A cylindrical tank subjected to internal pressure/? is simultaneously compressed by an axial force F = 72 kN (see figure). The cylinder has diameter d = 100 mm and wall thickness t = 4 mm. Calculate the maximum allowable internal pressure /?max based upon an allowable shear stress in the wall of the tank of 60 MPa.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.