Problem 4 The 7/8 in diameter pins at A and C that support the structure are in single shear. Find the largest force F that can be applied to the structure if the working shear stress for these pins is 5000 psi. Neglect the weights of the members. ANS: F = 3190 lb-f 5 of 6 2 ft Q 3 0 4 ft B 6 ft F 3 ft

Problem 4 The 7/8 in diameter pins at A and C that support the structure are in single shear. Find the largest force F that can be applied to the structure if the working shear stress for these pins is 5000 psi. Neglect the weights of the members. ANS: F = 3190 lb-f 5 of 6 2 ft Q 3 0 4 ft B 6 ft F 3 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

compute the force in member FJ
The wooden members in the simple truss below have the following capacity: Shear parallel to grain = 1 MPa, Compression parallel to Grain = 11MPa, Compression perpendicular to Grain = 5 MPa 1. Find the minimum safe x. a. 73 mm b. 160 mm c. 148 mm d. 112 mm 2. Find the minimum safe y. a. 15.97 mm b. 19.45 mm c. 9.14 mm d. 18.28 mm 3. Determine the stress in member AC. a. 1.13 MPa b. 1.258 MPa c. 1.224 MPa d. 1.04 MPa
Using method of sections, determine the reaction at A, the force in members BD, FE and CE if θ=30degrees, Φ=60degrees and d=12ft.
Two horizontal 5.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 1.01-in. diameter is used at each connection,determine the bearing stress (in psi) at Bin member AB.
Find the max tension on member DI in kN. Put "0" if none. a= 4.5m b= 4.8m c= 50kN d= 68kN
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places. Please answer all since they are all subquestions. Thanks Structural Theory 1d. Determine the vertical reaction R₂ in kN 1e. Determine the shear at midspan between vertical supports in kN. 1f. Determine the maximum factored load moment in the beam in kN.m
The pins on the frame at B and C each have a diameter of 0.25 inch. If these pins are subjected to doubleshear, determine the average shear stress in each pin if P1 = 500 lbs and P2 = 300 lbs
From the given truss shown, compute the force in member DE. a.62.5 N (C) b.187.5 N (C) c.62.5 N (T) d.37.5 N (C)
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 16 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 × 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at midpoint.
A sign of weight W is supported at its base by four bolts anchored in a concrete footing. Wind pressure p acts normal to the surface of the sign; the resultant of the uniform wind pressure is force F at the centerof pressure (C.P.). The wind force is assumed to create equal shear forces F/4 in the y direction at each bolt (see figure parts a and c). The overturning effect of the wind force also causes an uplift force R at bolts A and C and a downward force (-R) at bolts B and D (see figure part b). The resulting effects of the wind and the associated ultimate stresses for each stress condition are normal stress in each bolt (σu = 60 ksi); shear through the base plate (τu = 17 ksi); horizontal shear and bearing on each bolt (τhu = 25 ksi and σbu = 75 ksi); and bearing on the bottom washer at B (or D) (σbw = 50 ksi). Find the maximum wind pressure pmax (psf) that canbe carried by the bolted support system for the sign if a safety factor of 2.5 is desired with respect to the ultimate wind…
In the shown loaded truss, P = 225 kN, calculate the following and select the correct values from the given drop-down list: a) the support reactions at roller A and pin B (i.e., Ax, Ay & By ). 3 m b) the angle a. c) the forces in members AC and AB using the method of joints (i.e., FAC & FAB).
For the truss shown below is supported by a pin at A and roller at F. If it is loaded with P (kips)at joints B and E, determine the force in members AD, GH, BD, CE, and DG. P(kN) = 516