Problem 4: The uniform sign weighs 1500 lb and is supported by pipe AB, which has an inner radius of 2.75 in and an outer radius of 3 in. If the face of the sign is subjected to a uniform wind pressure of 150 psf, determine the state of stress at points E and D and show the results on a 3-D stress element. 12 ft B 150 lb/ft? 6 ft E F D -C 3 ft A

Problem 4: The uniform sign weighs 1500 lb and is supported by pipe AB, which has an inner radius of 2.75 in and an outer radius of 3 in. If the face of the sign is subjected to a uniform wind pressure of 150 psf, determine the state of stress at points E and D and show the results on a 3-D stress element. 12 ft B 150 lb/ft? 6 ft E F D -C 3 ft A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 30 mm. The outer diamter and thickness of the pressure vessel is 500 mm and 10 mm. Its length is 2m. Determine the maximum internal pressure (MPa) that can be applied if the longitudinal stress is limited to 155 MPa, and the circumferencial stress is limited to 55 MPa.
The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a length of 127 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 423 mm2 Ealuminum = 70 GPa.
A cylindrical tank has an inner radius of 750mm and length of 3.0m. Determine its minimum thickness (to nearest mm) if it is subjected to an internal pressure of 150kPa and tangential stress is not to exceed by 12MPa. Indicate the free body diagram
The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal stress in each rod if T2 = 400F, and also calculate the new length of the aluminum segment. Take aal = 13(10-6)>°F, Eal = 10(103) ksi, (sY)al = 40 ksi, acu = 9.4(10-6)>°F, (sY)cu = 50 ksi, and Ecu = 15(103) ksi
A column has an outside diameter, D = 550 mm, an inner diameter, d = 150 mm.Determine the average normal stress developed on the cross section if the load, F is1890 kN.
A thin hollow spherical container has a diameter 1 m and a thickness of 4 mm is subjected to an internal pressure. Determine the internal pressure the tensile stress of the element in the sphere is 500 kPa.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
The W-kg man stands in the position shown. If the center of gravity of the man is at Gand assuming that the contact point at C is smooth.a) Find the reactions at B and C. b) Determine the state of stress at point A on the cross section of the plank at sectiona–a (Cubic stress element in 2D).
A cylinder having an internal diameter of 20 in and an external diameter of 36 in is subjected to an internal pressure of 10000 psi and an external pressure of 2500 psi. Determine the hoop stress at the inner surface of the cylinder in psi.
Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa isa) 150 MPA b ) 125 MPa c) 175 MPa d ) 200 MPa e) none of these
The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a length of 126 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress (in MPa) post A. The posts are made of aluminum and have a cross-sectional area of 403 mm2. Ealuminum = 70 GPa. The correct answer is 887.66682. Show solution pls.
The horizontal force of P = 80 KN acts at the end of the plate. The plate has a thickness of 10 mm and P acts along the centerline of this thickness such that d = 50 mm. Plot the distribution of normal stress acting along section a-a.