Problem #5 a. A 30m steel tape is supported only at its ends and under a steady pull of 7kg. if the tape weighs 0.90kg, determine the (a) sag correction and (b) Correct distance between the ends of the tape. b. A 50m steel tape is supported only at its ends and under a steady pull of 8kg. if the tape weighs 0.90kg, determine the (a) sag correction and (b) Correct distance between the ends of the tape.

Problem #5 a. A 30m steel tape is supported only at its ends and under a steady pull of 7kg. if the tape weighs 0.90kg, determine the (a) sag correction and (b) Correct distance between the ends of the tape. b. A 50m steel tape is supported only at its ends and under a steady pull of 8kg. if the tape weighs 0.90kg, determine the (a) sag correction and (b) Correct distance between the ends of the tape.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c= 21 MPa, long bar fy = 415 MPa, calculate Using a T-beam geometry formed from monolithic construction, determine the effective flange width of a typical interior beam in mm.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: 8. Using a T-beam geometry formed from monolithic construction, determine the effective flange width of a typical interior beam in mm. = [bf] mm
A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c= 21 MPa, long bar fy = 415 MPa, calculate: Factored uniform load on a typical interior beam in kN/m using load factors of 1.2 for dead load and 1.6 for live load.
A 30-m steel tape weighs 1.5 kg and is supported at its end points and at the 5 and 15-meter marks. If a pull of 8 kg is applied, determine the correction due to sag between supports and for one tape length. Please include the complete solution
Question 45 Calculate the nominal shear strength (kN) of 4-legged stirrups 10-mm-diameter, spaced at 210 mm on centers for a beam with effective depth of 470 mm. Use yield strength of stirrups fy = 275 MPa.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: 7. Factored uniform load on a typical interior beam using load factors of 1.2 for dead load and 1.6 for live load. = [wu] kN/m (2 decimal places)
Determine the slenderness ratio and the Euler buckling load for round wooden dowels that are 2.15 m long and have a diameter of (a) 13 mm and (b) 28 mm. Assume E = 12 GPa.
A singly reinforced rectangular beam 350 mm wide and 450 mm deep is reinforced with 2 -16-mm-diameter bottom bars enclosed with 10-mm-dia stirrups covered with 40 mm of concrete. Calculate the nominal moment strength in kN-m. Use f'c = 24 MPa and fy = 280 MPa. Express your answer in two decimal places.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2.0 mon centers, on simple supports over a span of 6.0 m. The floor supports a superimposed servicedead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa,calculate: 7. Factored uniform load on a typical interior beam in KN/m using load factors of 1.2 for dead load and 1.6 forlive load.
A reinforced rectangular beam with width 437.5 and effective depth 692.5 is subjected to service liveand dead loads (self-weight included) of 56 and 70.5, respectively. If required, compressionsteel bars are to be placed at a distance d′ = 692.5 from the extreme compression fiber. Use ??′ =28 ??? and ??= 420 ???. Compute the following: 1. Solve for the area of tension steel bars using ?? = 0.004.2. Solve for the area of compression steel bars using ?? = 0.004.3. Solve for the area of tension steel bars using ?? = 0.005.4. Solve for the area of compression steel bars using ?? = 0.005
Complete Solution. Thank you! I'll rate asap. Given: a = 23.5 kN, b = 22.5 kN, c = 4.5 m Instructions: 3 Decimal Places Questions: a. Using Cantilever method, calculate for the force in kN at member DC. b. Using cantilever method, calculate for the axial force in kN at member CB. c. Using cantilever method, calculate for the axial force in kN at member FE. d. Using cantilever method, calculate for the axial force in kN at member CG. e. Using cantilever method, calculate for the axial force in kN at member GK.