Problem 5. A second-order pressure sensor having a damping ratio of 0.7 is used to measure is used to measure pressures having frequency content between 10 and 50 Hz. If the dynamic error must be within 10%, which of the following choices is an acceptable range for the sensor's natural frequency? (You can use the plot, which shows the magnitude ratio M2 as a function of a/w) (a) any natural frequency less than 100 rad/s (b) any natural frequency greater than 100 rad/s (c) any natural frequency betwecen 50 to 100 rad/s d) any natural frequency less than 50 rad/s (e) any natural frequency greater than 50 rad/s (f) None of the above

Problem 5. A second-order pressure sensor having a damping ratio of 0.7 is used to measure is used to measure pressures having frequency content between 10 and 50 Hz. If the dynamic error must be within 10%, which of the following choices is an acceptable range for the sensor's natural frequency? (You can use the plot, which shows the magnitude ratio M2 as a function of a/w) (a) any natural frequency less than 100 rad/s (b) any natural frequency greater than 100 rad/s (c) any natural frequency betwecen 50 to 100 rad/s d) any natural frequency less than 50 rad/s (e) any natural frequency greater than 50 rad/s (f) None of the above

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A first order instrument has the input F(t)=10sin(ω.t) . The static sensitivity is 2.5 output units per unit input. Time constant is 0.2 .Compute the phase angle and the maximum value of x(t) for ω=0.1 and 100 rad/sec.
The acceleration time waveform was obtained from the outboard bearing of a rotor with a looseness problem. The waveform can be described by the equation: A(t) = 0.36sin(1050t +0.07) + 0.21sin(2100t-0.11) + 0.13sin(3150t) – 0.05sin(4200t) g 1. Determine the minimum number of samples for measuring the signal, based on a Nyquist Factor of 2.56. 2. List the frequencies and acceleration amplitudes that appear in the resulting frequency spectrum if an ideal bandpass filter rated at 170 Hz and 600 Hz is applied.
A displacement transducer has the following specifications: Linearity error:±0.25% reading Drift:±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V Output: dc 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltme- ter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Estimate an uncertainty in a nominal displacement of 2 cm at the design stage. Assume 95% confidence.
A temperature measurement system is composed of a sensor and a readout device. The readout device has a claimed accuracy of 0.6 °C with a resolution of 0.1 °C. The sensor has an off-the-shelf limit of error of 0.5 °C. Estimate a design-stage uncertainty in the temperature indicated by this combination. A displacement transducer has the following specifications: Linearity error:±0.25% reading Drift:±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V Output: dc 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltme- ter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Estimate an uncertainty in a nominal displacement of 2 cm at the design stage. Assume 95% confidence.
The mass of a solid hemisphere is measured once with a digital balance whose resolution is 1 g. The result is m = 50 g. With a caliper, the resolution of which is 0.05 mm, repeated measurements of the diameter D of the hemisphere are carried out. The values obtained for D: 100.30 mm; 100.00 mm; 100.60 mm; 100.10 mm; 100.25 mm; 100.50 mm; 100.40 mm; 100.20 mm; 100.30 mm; 100.35 mm. The result of measuring the mass m is: (a) (50 ± 1) g (b) (50.0 ± 0.58) g (c) (50.00 ± 0.58) g (d) (50.0 ± 0.5) g
A vibrometer with mass 0.86 kg and damping ratio ζ 0.62 is designed to measure vibration in the frequency range ωb = 34.8-84.7 rad/sec. Chose the appropriate stiffness from the given values to guarantee the maximum error will not exceed 2% Note:ZY=r2(1−r2)2+(2rζ)2√ a. 115 N/m b. 367 N/m c. 85 N/m d. 2173 N/m e. 680 N/m
1- I need answer of all sub-parts questions. Thanks The figure shows a simple model of a motor vehicle that can vibrate in the vertical direction while traveling over a rough road. The road surface varies sinusoidally with an amplitude of 0.01 m and a wavelength of 6 m. The vehicle has a mass of 1007 kg. The suspension system has a total spring constant of 40 kN/m and a damping coefficient of 20 kN.s/m. The vehicle average speed is v = 100 km/hr. The objective is to determine the vehicle steady-state displacement amplitude as well as the respective transmitted force. Calculate the forcing frequency of the pumpy road. Calculate the natural frequency of the vehicle SDOF system. Calculate the damping ratio of the vehicle SDOF.
Question / Draw an accelerometer sensitivity curve and discuss the useful frequency range. In thesame plot also show the effect of increased accelerometer mass? (Please answer it in very easy way easy to rememeber for revsison )
i just need final answer A coaxial capacitive sensor is desired to measure the water level in a water tank. The coaxial sensor with a length of d=32 cm has an inner radius of a=9 mm and an outer radius of b=12 mm. Since the total capacitor value is measured at the sensor output 4.03 nF, the water level l =? Calculate (Note: It is known that the water temperature in the tank is 20 degrees. The variation graph of the relative dielectric constant with temperature is also given below.)a- 15cm b- 12cm c- 21cm d-18cm e- 26cm
Experiments are repeated and two separate acceleration peaks separated with the damped vibration period are found as 0.53 g and 0.28 g, respectively where g is the gravitational acceleration. The uncertainty with the acceleration measurement is found to be 0.03 g from the manufacturer manual. We would like to report the damping ratio. What is the mean value of the damping ratio and uncertainty in the damping ratio calculation.?
The ability of the instrument to give same output for same input when the conditions are different is known as __________________ a. Repeatability b. Resolution c. Reproducibility d. Accuracy