Answered: Problem 6 For the structure shown in…

Problem 6 For the structure shown in the figure, determine the normal and shear stresses at point A on the cross section of the pipe at section a-a. Section a 50 mm 40 mm JOAN 300 mm 3000 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.7P: The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the...

See similar textbooks

Related questions

Q: A simply supported wood beam with a span of L=12 ft supports a uniformly distributed load w. The…

Q: 3.9 A thin cylindrical steel drum, 10 mm thick, is subjected to an internal pressure of 1,5 MPa and…

A: Given data: N=259 rpmσ=120 MPa Need to determine the diameter of the drum.

Q: Fluid flows into a junction at a flowrate Q, and exits via two pipes of equal diameter, as shown in…

Q: P₂ * 1/3 + 2,5-1,8 = 2/3 +² ₂ === Y OB.h₂ = (2₂-2₂) +h, OCP₁ 7 -2₁ - 1₁ + 1 = 21/2² +2₂ 7 - +²₂+. 2g…

A: Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m Suction line:…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: Compute the potential evaporation for amsterdam for the month of july if the net radiation is 361…

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: is made of steel of 400mm². Use ne the vertical and A 1 m 2.5 kN -1 m E B D 1 m

Q: The wave resistance of a model of a ship at 1/19 scale is 2 lbf at a model speed of 7 ft/s. What are…

Q: A 3200-lb automobile whose speed is 60 mi/h has a kinetic energy of? a. 1.8 x 10 5 ft.lb c. 3.9 x…

Q: Determine the magnitude of the moment Mc for the cantilever beam, where P = 33 kips, w = 7 kips/ft,…

Q: Shown in the Figure is the complete pump performance chart for a 3×4-10 centrifugal pump at 1750…

A: Given Total head, H = 50 ft = 15.24 m Speed, N = 1750 rpm Flow rate, Q = 200 gal/min =…

Q: A 1.625-in.-diameter solid steel shaft supports loads PA = 340 lb, Pc = 540 lb, and PE = 340 lb, as…

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to…

Q: L₁ Answer: vg: (1) i a B P b (2) mm. C L2

Q: determine the largest weight of block D without causing motion.

Q: The beam is made from a material that can safely support a tensile or compressive stress of 350 MPa.…

Q: Figure shows a pipe system. At the entrance to the pipe (point 1), the diameter is d₁ and it is a…

A: Given: p1 =ϕ1

Q: In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: Determine the magnitude of the vertical force C, for the simply supported beam, where w = 11…

Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of…

Q: In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: Consider a causal second-order system with the transfer function 1 G(s) = 1+2s+s² 1 with a unit-step…

Q: Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable…

A: Given data: ◆ The tension in the rope ABC = 74 lb ◆ The angle made by cable ABC with horizontal =…

Q: A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the…

Q: A steel [E = 29,200 ksi; a = 6.0 x 106/°F] pipe column (1) with a cross-sectional area of A₁ = 5.40…

Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of…

A: Given data: Initial speed of the ball (vo) = 179 mi/hr Angle of projection (α)=17o Concept: In the…

Q: Air enters a humidifier at 20.25 C and 30% RH. The air is at a constant pressure of 101.325 kPa. If…

Q: A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the…

Q: 3: The heat transfer Q from the steam turbine shown in figure below is 8.5 kJ/s. Determine me power…

Q: Problem 1 A 30 wt% Sn-70 wt% Pb alloy is heated to a temperature within the aliquid phase region. If…

A: Problem 1: The unknown temperature with unknown phase composition marked on Pb-Sn diagram is given…

Q: 8" 49 6" 90° -X Determine the location of the centroid of the composite figure shown.

A: For the given composite figure we have to determine the location of the centroid.

Q: The composite simply supported steel shaft is subjected to a force of 2P2PP = 16 kNkN at its center.…

A: To find maximum deflection

Q: Calculate the moment of inertia of the shaded area about the x-axis. 98 mm 98 mm 52 mm Answer: lx =…

Q: A steam power plant operates on the ideal Rankine cycle. The boiler pressure is rated at 5 MPa and…

A: Given problem is

Q: F. Determine to 2 decimal the magnitude of the normal stress in rod (1) places

Q: Calculate the moment of inertia of the shaded area about the x-axis. 117 mm 36 mm ·-+-· 64 mm 64 mm…

A: Given data: ◆ The base of the triangle: b = (64 + 64) mm = 128 mm ◆ The height of the triangle: h =…

Q: A cylinder of radius R and mass M is tied to a rope that connects it to a box of mass m, through a…

Q: Two forces FA =185 lb and FB =189 lb are acting on the bracket shown with axes x,y,v and w…

Q: Brass (2) Aluminum (1) Brass (2) b d₂ d₁ d₂

Q: The Figure shown below is a parallel pipeline system with two branches used to supply lubricating…

Q: Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel…

Q: How does resurfacing the cylinder head of an OHC engine affect valve timing and what should be done…

A: Given question: How does resurfacing the cylinder head of an OHC engine affect valve timing and what…

Q: The grains of wood in the board make an angle of 20 with the horizontal as shown. Using Mohr's…

Q: A 5-m-long simply supported timber beam carries two concentrated loads as shown. If L = 28 kN and M…

Q: Compute (I bar sub x, in mm4, round-off to 2 decimal places) for the region shown. X

Q: From the figure shown, if b = 3 units, determine: Inclination of the principal axes, in degrees…

Q: A 6-mm-diameter electrical transmission line carries an electric current of 50 amperes and has a…

A: Given- parameter given- diameter= 6mm current= 50A resistance= 0.002ohm/mt. length k=218w/m-k

Q: The two shafts are made of A992 steel. Each has a diameter of 0.9 in., and they are supported by…

A: Given data: E=11×103 ksi Need to determine the angle of twist of end A.

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

Problem 6 For the structure shown in the figure, determine the
normal and shear stresses at point A on the cross section of the pipe
at section a-a.
50 mm
Section a a
300 mm
300 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A solid circular bar having diameter d is to be replaced by a rectangular tube having cross-sectional dimensions d × 2d to the median line of the cross section (see figure). Determine the required thickness tminof the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A pole is fixed at the base and is subjected to a linearly varying distributed force with maximum intensity of q0and an axial compressive load P = 20 kips at the top (see figure). The pole has a circular cross section with an outer diameter of 5 in. and an inner diameter of 4.5 in. Find the normal stresses on the surface of the pole at the base at locations A and B.
Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure. The rack is made up of 2 in. x 2 in. steel tubing which is 1/8 in. thick. Assume that the weight of each of four bicycles is distributed evenly between the two support arms so that the rack can be represented as a cantilever beam (ABCDEF) in the xy plane. The overall weight of the rack alone is W = 60 lb directed through C, and the weight of each bicycle is P = 30 lb.
The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
A traffic light and signal pole is subjected to the weight of each traffic signal We = 45 lb and the weight of the road lamp WL= 55 lb. The pole is fixed at the base. Find the principal normal stresses and the maximum shear stress on element B located 19 ft above the base (see figure). Assume that the weight of the pole and lateral arms is included in the signal and lamp weights
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.