Problem 6 The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 75 mm wide. The coefficient of friction is 0.20. The maximum lining interface pressure is pV=1.5 MPa.m/s. (a) Find the brake torque, necessary force P, and steady-state power. (b) Complete the free-body diagram of the drum. Find the bearing radial load that a pair of straddle-mounted bearings would have to carry 75 mm-

Problem 6 The figure depicts a band brake whose drum rotates counterclockwise at 200 rev/min. The drum diameter is 16 in and the band lining 75 mm wide. The coefficient of friction is 0.20. The maximum lining interface pressure is pV=1.5 MPa.m/s. (a) Find the brake torque, necessary force P, and steady-state power. (b) Complete the free-body diagram of the drum. Find the bearing radial load that a pair of straddle-mounted bearings would have to carry 75 mm-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
A block brake with a torque of 250 N-m. Its drum rotates at 100 rpm. The length of the block (1) is twice its width (w). Assume, the coefficient of friction P is 0.35. Calculate: (1) the applied load (P) and the hinge-pin reaction (Rx ana Ry) for clockwise rotation of the drum; (2) the applied load and hinge-pin reaction for anticlockwise rotation of the drum; (3) the rate of heat generated during the braking action. (4) The dimensions of the block, if the intensity of pressure between the block and brake drum is 1 MPa. (5) Check whether the brake is self-locking.
Example Problem #4 A disk brake has two pads which cover 45 degrees of the disk. The outside radius is 6.0 inch and the inside radius is 4.0 inch. Assume a coefficient of friction of 0.4, and a max pressure, pa-100 psi a) Find the force required to apply one pad. b) Find the torque capacity for both pads.
A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.
A conical Clutch transmits rotation from one rotating shaft to another though frictional forces on the conical face. The following data is for a conical clutchInside Diameter 25.0 mmOutside Diameter 100 mmCoefficient of Friction 0.33Axial Force 1000NIncluded angle 100 degreeRotational speed 1500rev/minuteCalculate the Torque and Power that can be transmitted without slipping using both Uniform Pressure Theory and Uniform Wear Theory
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
A double square threaded power screw has an efficiency of 65% when raising a load. Friction angle for threads is 8.54o, with collar friction negligible. The pitch diameter of the screw is 70 mm. When lowering a load, a uniform speed is maintained by a brake. If the load is 10 tons, what torque must be exerted by the brake? Is this screw self-locking?
The width of the simple band brake shown in the figure is 30 mm. The coefficient of friction between the brake and the drum surface is 0.20. Determine the braking torque and thickness of the band if the tensile stress is not to exceed 65 N/mm2.
5.) A double-acting 12-cylinder, 4-stroke cycle engine with a cylinder diameter of 240 mm operates at 2,400 rpm. The prony brake arm at 1.24 meters registered an equivalent braking load of 0.24 metric ton. Calculate the brake mean effective pressure in psi. the piston travels 1.24 times its diameter
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
Two pulleys, one 425mm diameter and the other 210mm diameter are one parallel shaft 2m apart and are connected by a crossed flat belt. Find the length of the belt required and the angle of conduct between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 200 rev/min, if the maximum permissible tension in the belt is 1 kN, and the coefficient of friction between the belt and pulley is 0.3?
In Fig. 6-38 the maximum lining pressure for any point on the brake is to be limited to 100 psi; μ = 0.2. Find the torque capacity of the brake and the value of force P. Ans. T = 9,080 in-lb, P = 487 lb