Problem 8: An aluminium pipe column (6.5- inches outside diameter; 0.250 inches wall thickness) supports a load of 11 kips. The aluminium pipe rests on a square steel base plate, which in turn rests on a concrete slab. Determine the bearing stress between the aluiminium pipe and the steel plate 11 kips Outside diameter = 6.5 in Wall thickness = 0.25 in. Square steel base plate Concrete slab Problem 9: Use the same situation as problem 8. If the bearing stress of the steel plate on the concrete slab must be limited to 90psi, what is the minimum allowable plate dimension a?

Problem 8: An aluminium pipe column (6.5- inches outside diameter; 0.250 inches wall thickness) supports a load of 11 kips. The aluminium pipe rests on a square steel base plate, which in turn rests on a concrete slab. Determine the bearing stress between the aluiminium pipe and the steel plate 11 kips Outside diameter = 6.5 in Wall thickness = 0.25 in. Square steel base plate Concrete slab Problem 9: Use the same situation as problem 8. If the bearing stress of the steel plate on the concrete slab must be limited to 90psi, what is the minimum allowable plate dimension a?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The lower plate is stationary, the upper plate moves at a velocity of 10 ft/s. Oil (SAE 10W-30, 150 °F) which fills the space. The variation in velocity of the oil is linear. What is the shear stress in the oil? : Two plates are separated by 1/4 inch
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
11-58. The measured strains for an equiangular rosette, attached to a stressed aluminum alloy member,are E0 = +400 micro m/m,E60 = +400 micro m/m, and E 120 = -600 micro m/m. What are the principal stresses and in which directions do they act?Given E =70 GPa, and v = 0.25.
Q4) two plate one lower fixed and one upper moved with a velocity 0.3 m/s , thedistance between the two plate is 0.3 mm and viscosity of the liquid is 0.65*10-3kg/m.s , calculate the shear stress on the upper plate .
For the point given the plane stress state, which of the following is the correct type and limit values of Mohr Circle? sx =-40 MPa (Bası), sy =60 MPa (Çeki) txy =60MPa
A WATER TANK IS 5 IN DIAMETER AND 6 HIGH. IF THE TANK IS TOBE COMPLETELY FILLED, DETERMINE THE MINIMUM THICKNESS OF THETANK IF THE STRESS IS LIMITED TO 70 MPa.(note: Diam = 5, Height = 6)
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
A large uniform cylindrical steel rod of density ρ = 8.8 g/cm3 is 4.0 m long and has a diameter of 5.0 cm. The rod is fastened to a concrete floor with its long axis vertical. What is the normal stress in the rod at the cross section located at (a) 2.0 m from its lower end? (b) 2.5m from the lower end? Your answer
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 2. Assume P = 80 kN and Q = 140 kN.
A steel propeller for a windmill transmits 4.4 kW at 43 rpm. If the allowable shear stress in the shaft must be limited to 41 MPa, determine the minimum diameter d required for a solid shaft.
The wooden section of the beam is reinforced with two steel plates as shown. If the beam is subjected to a moment of M = 5.0 kN. m, determine the maximum bending stresses in the steel and wood. Sketch the stress distribution over the cross section. Take Ew = 11 GPa and Est = 200 GPa
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2).