Problem 9-65: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe. 200 lb 200 lb 20 lb-ft 20 lb-ft

Problem 9-65: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is subjected to an internal pressure of 500 psi and the axial tension and torsional loadings shown, determine the principal stress at a point on the surface of the pipe. 200 lb 200 lb 20 lb-ft 20 lb-ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

A thin-walled pressure vessel is made of steel with a thickness of 2 mm and an internal diameterof 300 mm. It is subjected to an internal pressure of 10 MPa. Determine the hoop stress andlongitudinal stress developed in the vessel.
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
A spherical pressure vessel has an outer diameter of 75 mm and a wall thickness of 10 mm. It's made of a steel having the yield strength (Sy) of 300 MPa. If the largest principal normal stress is not to exceed 80% of the yield strength, determine the maximum internal pressure this pressure vessel can withstand. The pressure vessel is considered thick-walled spherical pressure vessel.
A steel pipe with an outer diameter of 50 mm and a wall thickness of 5 mm is subjected to aninternal pressure of 10 MPa and an axial load of 20 kN at an angle of 45 degrees to the axis of thepipe. Determine the maximum axial stress and maximum hoop stress developed in the pipe.
Determine the average normal stress developed at points A, B, and C. The diameter ofeach segment is indicated in the Figure below.
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
It is known that the seam, which is rotated 45∘ from the vertical, as shown in Fig. E3-c, will fail if subjected to a tensile stress of 25 kPa or a shear stress of 1 kPa. Determine the normal stress and shear stress acting on the seam, and state if the seam will fail due to the loading indicated
A cylindrical steel pressure vessel has an inner radius of 24 inches and wall thickness of 0.25 inches. Determine the tangential and longitudinal stresses when the vessel is pressurized to 125 psi.
The shaft assembly is made from a steel tube 1 in. in diameter,which is bonded to a solid brass core 0.5 in. in diameter. If atorque of 250 lb-ft is applied at its end, determine the maximumshear stress in psi experienced by the assembly. Take G for steelat 11.4x103 ksi and G brass at 5.2 x 103 ksi.
Determine: a) State of stress at point A on the upper surface of the shaft b) The maximum normal stresses at point A as we well as its orientation c) Of the 800lb force is going upwards (instead of downwards) explain what will happen to i) normal stress, and ii) shear stress at A (no calculations needed for part c)
8-1. The state of stress at a point is shown on the element. Determine (a) the principal stress and (b)the maximum in-plane shear stress and average normal stress at the point. Specify the orientationof the element in each case. Show the results on each element.
A cylindrical pressure vessel is fabricated from steel plates whichhave a thickness of 20 mm. The diameter of the pressure vessel is 500 mm andits length is 3m. Determine the maximum internal pressure which can be appliedif the stress in the steel is limited to 140 MPa.