A linear actuator having a in single-thread Acme screw is used to raise a load of 1600 lb. A plain thrust collar having a 0.8 in mean diameter is used. Coefficients of running (kinetic) friction are estimated as μ= 0.13 and c = 0.1. a.) Determine the screw pitch, lead, thread depth, mean (pitch) diameter, and lead angle. b.) Estimate the torque needed to raise the load. c.) Estimate the "overall" efficiency of the linear actuator when raising the load. 0.125 in, h 0.0625 in, dm 0.5625 in, λ = 4.046° Ans. a.) P = 0.125 in, L b.) TLR = 157.1 in lb = 13.09 ft lb c.) 17 = 20.26%

A linear actuator having a in single-thread Acme screw is used to raise a load of 1600 lb. A plain thrust collar having a 0.8 in mean diameter is used. Coefficients of running (kinetic) friction are estimated as μ= 0.13 and c = 0.1. a.) Determine the screw pitch, lead, thread depth, mean (pitch) diameter, and lead angle. b.) Estimate the torque needed to raise the load. c.) Estimate the "overall" efficiency of the linear actuator when raising the load. 0.125 in, h 0.0625 in, dm 0.5625 in, λ = 4.046° Ans. a.) P = 0.125 in, L b.) TLR = 157.1 in lb = 13.09 ft lb c.) 17 = 20.26%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A winch drum of diameter 161 mm turning at 12pm lifts a load of 7.5kN. What is the winch output power?
A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to raise the load without friction effect? Group of answer choices 66845 N-mm 133690 N-mm 236078 N-mm 334840 N-mm
A single-threaded power screw of square form is to raise a load of 90KN at the rate of 360mm/min. Other data are as follows: Nominal Diameter of screw = 36mm Pitch = 6mm Coefficient of thread friction = 0.1 Coefficient of collar friction = 0.08 Friction radius at collar= 30mm Determine the power input to the screw in kilowatts.
A nut which is connected to a lead screw is moved in a horizontal plane against a force of 100kN at a speed of 4mm/sec by electric motor powered screw. The following data is given Single start square thread screw Pitch of the screw = 6mm Outlet diameter of the screw = 40mm Co-efficient of friction of the screw thread = 0.15 Efficiency of the motor = 85% Determine the power required and efficiency of the screw
How much torque can a cone clutch transmit if the angle of the conical elements is 10 degrees. The mean diameter of conical sections is 200 mm and an axial force of 600 N is applied. Consider a coefficient of friction
A bilge pump requires 380 N.m torque at about 320 rpm. It is driven by an 1160 rpm motor by means of a roller chain. The nature of service calls for a service factor of 1.5. If the total efficiency of transmission is 95 percent, what is : The size of the motor? Number of sprocket teeth? The pitch and number of strands of the chain required?
n Mukwano Industries, a shaft assembly shown in Fig. 2 is driven by a flat belt at location A and drives a flat belt at location B. The drive belt pulley diameter is 300 mm; the driven belt pulley diameter is 500 mm. The distance between sheaves is 800 mm, and the distance from each sheave to the nearest bearing is 200 mm. The belts are horizontal and load the shaft in opposite directions. Determine the size of the shaft using Distortion Energy Theory (DET) and the types of steel that should be used. Use a safety factor of 10. Also, provide a free-body diagram as well as moment and torque diagrams
I want right solution plz solve if you know 100% flange coupling connects two 50 mm diameter lengths of commercial shafting. The coupling flanges are bolted together with four bolts of the same material as the shaft. The bolts are set in clearance holes. The diameter of the bolt circle is 240 mm and the flange thickness is 22 mm, Determine the minimum bolt diameter required to transmit the same torque that the shaft can transmit. What power may be transmitted at 200 rev/ min under steady load conditions?
The energy required to shear a 1-in. round bar is approximately 1000 ft-lb. In use, the shearing machine is expected to make a maximum of 40 cutting strokes a minute. The frictional losses should not exceed 18 % of the motor output. The shaft carrying the flywheel is to average 150 rpm. (a) What motor horsepower is required? (b) Assuming a size of flywheel and choosing appropriate f C, find the mass and sectional dimensions of the rim of a cast-iron flywheel. The width of the rim is to equal the depth and is not to exceed 3 ½ in. It would be safe to assume that all the work of shearing is supplied by the kinetic energy given up by the flywheel.
A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Estimate the efficiency of the jack for raising the load. (b) Estimate the power required to drive the screw at a constant 1 revolution per second. Schematic and Given Data: Load 50 kN
A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of the screw and the thrust collar mean diameter are known. Running friction coefficients are estimated. Find: (a) Determine the thread depth and helix angle. (b) Estimate the starting torque for raising and lowering the load. . Schematic and Given Data: Load 50 kN
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron