Problem 9.131 A circular V-belt has an inner radius of 600 mm and a cross-sectional area as shown. (Figure 1) Figure 1 of 1 75 mm Part A Determine the volume of material required to make the belt. Express your answer to three significant figures and include the appropriate units. V= Submit μA Value Units My Answers Give Up ?

Problem 9.131 A circular V-belt has an inner radius of 600 mm and a cross-sectional area as shown. (Figure 1) Figure 1 of 1 75 mm Part A Determine the volume of material required to make the belt. Express your answer to three significant figures and include the appropriate units. V= Submit μA Value Units My Answers Give Up ?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter6: Fundamental Dimensions And Units

Section: Chapter Questions

Problem 38P

See similar textbooks

Similar questions

A thin walled spherical tank is filled with water at a pressure of 4666 psig, the tank’svolume is then 805.407 in3. If the water is released from the tank, how many poundswill be collected at atmospheric pressure? Use 305 000 psi as an average value of bulkmodulus of elasticity
Show complete solutions. (2 decimal places) 1. Imagine the plumb bob as a perfect cone, compute for the volume of steel needed to make thecone if the dimension are a diameter of 60 mm and a height of 40 mm. The height of a cone shaped tank for liquid storage in a chemical factory is 9 ft with a diameter of14 ft. a) what is the volume of liquid the tank can hold in cubic feet? (5 pts); b) if the storage tankreleases water with a rate of 350 liters per minute, how many minutes will it take for the tank beemptied?
the answer given is 31.9kg. How to calculate the mass of a 2 m length of schedule 40 pipe, nominal size 101.6?
a curious traveler asked this question on stack exchange: a flight from los angeles to albuquerque is about 2 hours but is approximately equal to 670.2miles. a flight from san jose to chicago is 4 hours but is approximately equal to 1859.0 miles. can anyone explain why the travel time from san jose to chicago is not longer and closer to 5.75 hours? if the distance increase by 2, shouldn't the time increase by a factor of 2 as well? a) write a linear model for this question. takeoff and landing will take a fixed amount of time. actual travel in the air will take time proportional to the distance traveled. identify the slope and intercept with their units. b) use the data in the quotation to estimate the two constants in your linear model.
Asap please try to solve faster I will like
Show complete solution with figures A rigid container having outside diameter of 30 mm and thickness of 5 mm contains water of height 700 mm.What will the column length be if a force of 5 kN is applied to its open end by a frictionless plunger? Assume noleakage. Use 2.2 GPa for bulk modulus of elasticity of water. a) 689 mm b) 525 mm c) 527 mm d) 695 mm e) None
these are the answers I only need solutions 1. f = 8.42 MPa 2. Mcr= 121.0 kN-m 3. fconc= 10.42 MPafsteel= 197.22 MPaf’steel= 104.30 MPa
An expansion tank for a domestic hot water system measures 73⁄4 inches indiameter and 201⁄4 inches long. What is the maximum volume the tank canhold?
1)Coefficient of elasticity of a fluid E = 200000 t / m²Considering that for 1 Atmosphere (10 t / m²) pressure increase, the ratio of the decrease in the volume of this fluid to the initial volume iswhich one is given correctly?a) 0.00003b) 0.000004c) 0.00005d) 0.00006e) 0.00007 Please write clearly and clearly. thanks in advance
Solve it correctly please. I will rate accordingly.
PLEASE ANSWER QUESTION #1 ONLY, DISREGARD THE OTHER PROBLEMS GIVEN. SHOW COMPLETE SOLUTION. THANK YOU. An 8 ft diameter by 16 ft height vertical tank is receiving water (? = 62.5 lb/ft3) at the rate of 295 gal/min and discharging through a 4-in ID line with a constant speed of 6 fps. At a given instant, the tank is half full. Determine the following: QUESTION #1: the mass change in the tank (sample answer: 20,287.65 lb. round off to 2 decimal place QUESTION #2: the water level in the tank 15 min. later (sample answer: 20,287.65 ft round off to 2 decimal place QUESTION #3: the volume change in the tank (sample answer: 20,287.65 cu ft round off to 2 decimal place
An open-topped tank is to be cylindrical in shape and have volume 50m3. The cost of the material for the circular base is £38 per m2. The cost of the material used for the curved surface is £(38 + 10) per m2. By first finding a function for the total cost of materials in terms of the radius of the tank, use differentiation to find the radius and height of the tank that minimises the total cost of materials. Give your answers in m, to 2 decimal places.