PROBLEM EXERCISE - ASSIGNMENT The cross-sectional area of an aluminum bar is 160 mm? It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 70 MPa. Assume the bar is suitably braced to prevent buckling. Draw the diagram and show your solution. Add the 2nd to the last digit of your i.d. number in the loads only. Ex: 202013178... 12+7=19, 16+7=23, 33+7=40, 30+7=37 19KN 16KN 33KN 30KN 1.0m 1.80m 0.70m

PROBLEM EXERCISE - ASSIGNMENT The cross-sectional area of an aluminum bar is 160 mm? It carries an axial loads at the positions as shown in the figure. Compute the total deformation of the bar if E = 70 MPa. Assume the bar is suitably braced to prevent buckling. Draw the diagram and show your solution. Add the 2nd to the last digit of your i.d. number in the loads only. Ex: 202013178... 12+7=19, 16+7=23, 33+7=40, 30+7=37 19KN 16KN 33KN 30KN 1.0m 1.80m 0.70m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
A steel rod of 30 mm diameter is inserted in a copper tube of external diameter 45 mm and an internal diameter of 37 mm carries a load of W =1750kN. The length of this compound bar is 180 mm. If, ES= 2 × 105 N/mm2and ECu= 1 × 105 N/mm2, calculate the stresses developed in copper and steel.
A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? α=11.7x〖10〗^(-6)/°C and E = 200GPa. See figure 06
AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGHTS SHOWN. IN THE FIGURE . IF E= 85 kpA , compute the total deformation. Assume that the bars are suitably braced to prevent buckling.
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa. Express your final answer in N.m to the nearest whole number. Do not include the unit in your answe
Tempered rod with length of c= 8m and cross sectional dimensions a=297 mm is carrying an axial load P=75kN if the modulus of elasticity is 185gpa determine the elongation
AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E = 75 KPa, COMPUTE THE TOTAL DEFORMATION. ASSUME THAT THE BARS ARE SUITABLY BRACED TO PREVENTBUCKLING. ALSO, DRAW THE AXIAL FORCE DIAGRAM.
A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjectedto a 6000 lbs tensile load acting along its width. Find the deformation along its length andthickness if poison’s ratio is 0.27.
The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown below. The properties of the segments and the working stresses are listed in the table. Determine the maximum allowable value of P in kips if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the steel given that P= 96.3 kN? Express your answer in two decimal places.
A steel rod bar 250 mm long has a diameter of 10 mm and fits concentrically inside a bronze tube of the same length. The outside diameter of the bronze is 15 mm has a wall thickness of 2 mm. The r bar and the tube are connected by rigid end plates, so that they twist together. The composite shaft is designed to transmit 16 N.m torque. Take Gsteel=80 GPa and Gbronze=30 GPa. Calculate the torsional stiffness for each The torque transmitted by each shaft The maximum shear stress in each The angle of twist in degrees
A steel bar of rectangular cross section 45 mm (height) x 60mm (base) and pinned at each end is subject to axial compression. The proportional limit of the material is 320 Mpa and E= 200 GPa. -Find least Radius of Gyration (in mm)? -Determine the transition length (in mm) in which the Parabolic formula may be used instead of the Euler's equation.? -Determine the transition slenderness ratio in which the Parabolic formula may be used instead of the Euler's equation.? -If the Length is 1 meter, determine the critical load (in KN) using pin support. -if the length is 3 meters, determine the critical stressn(in MPa) using pin support.