Problem The enthalpy of a system is given by the equation H = U + PV where U is the internal energy, P = pressure, and V = volume. In addition, the internal energy, U = Q + W where Q is the heat and W is the work. Suppose we want to find the rate of change in the enthalpy at constant pressure of 1.25 atm, what is the value when heat is absorbed by the system at a rate of 45 J/s and work is done by the system at a rate of 100 J/s when the change of volume is rated at 35 x 10 m%s? 1. What is the change in heat with respect to time? 2. What is the change in internal energy of the system with respect to time? 3. What is the change in enthalpy of the system with respect to time?

Problem The enthalpy of a system is given by the equation H = U + PV where U is the internal energy, P = pressure, and V = volume. In addition, the internal energy, U = Q + W where Q is the heat and W is the work. Suppose we want to find the rate of change in the enthalpy at constant pressure of 1.25 atm, what is the value when heat is absorbed by the system at a rate of 45 J/s and work is done by the system at a rate of 100 J/s when the change of volume is rated at 35 x 10 m%s? 1. What is the change in heat with respect to time? 2. What is the change in internal energy of the system with respect to time? 3. What is the change in enthalpy of the system with respect to time?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters a throttling valve as a two-phase mixture at a pressure of 20 bar and a speed of 15 m/s. It leaves the valve at a pressure of 1 bar and a temperature of 120 -C.(a) Find the quality of the incoming steam.(b) Find the output speed.
Water vapors at 40 bar enters a pipe fitting (adapter) with a velocity of 169 m/s and exits thefitting at 10 bar and 572°F. If the temperature at the inlet is 1004°F., calculate the exit velocity.The system is assumed to be at steady state.
A steam trap is a device to purge steam condensate from a system without venting uncondensed steam. In one of the crudest trap types, the condensate collects and raises a float attached to a drain plug. Whenthe float reaches a certain level, it “pulls the plug,” opening the drain valve and allowing the liquid to discharge. The float then drops down to its original position and the valve closes, preventing uncondensed steam from escaping.(a) Suppose saturated steam at 25 bar is used to heat 100 kg/min of an oil from 135°C to 185°C. Heat must be transferred to the oil at a rate of 1:00 x 10 4 kJ/min to accomplish this task. The steam condenses on the exterior of a bundle of tubes through which the oil is flowing. Condensate collectsin the bottom of the exchanger and exits through a steam trap set to discharge when 1200 g of liquid is collected. How often does the trap discharge?(b) Especially when periodic maintenance checks are not performed, steam traps often fail to close completely…
Nitrogen flows at 1000 kg/h into a compressor at 1 bar and 300 K and leaves at 5 bar and 420 K, Cooling water flows through the compressor at the rate of 1400 kg/h, entering at 300 K and leaving at 320 K. a) How much power is supplied to the compressor? b) With the same cooling water flow rate and inlet temperature, calculate the minimum power required to attain the same change in state of nitrogen. c) What is the efficiency of the compressor?
Air flows through a nozzle. It enters at 20 bar and 1100°F and exits at 10 bar and 800°F. The inlet diameter ratio between outlet diameter is 3. Consider steady state, determine air inlet and outlet velocities, in ft/s
In the following question you may ignore changes in elevation and velocity of the fluid. (a) In a steam power plant liquid water enters the boiler at a temperature of 40°C and exits as wet steam at a pressure of 15 bar with a dryness fraction of 0·95. Find the heat transfer per kg to the steam. (b) The wet steam passes through a superheater and emerges at a pressure of 15 bar and temperature of 300 °C. It then passes through a turbine, generating 400 kW of power as it does so, and comes out as wet steam at a pressure of 1 bar. The mass flow rate is 0·57 kg/s. There is no heat loss from the turbine. (i) Show that the exit specific enthalpy is about 2337 kJ/kg. (ii) Find the dryness fraction of the steam at the turbine exit. (c) Sketch the T-S diagram for the Rankine (steam plant) cycle and describe the processes. Also indicate on the diagram the points corresponding to the inlet and outlet of the boiler, superheater and turbine.
In the boiler of a steam engine the superheated steam is at 500 degrees Celsius and 20 mPa is created by adding an amount of heat to the pressured water. Erros up to 10% have come up. Find the ideal gas law. Could the error seen in testing be due to the ideal gas law assumption? - value from the ideal gas law - value from tables - %Error Which of the above values is the most accurate? Could the error seen in testing be due to the ideal gas law assumption?
When air expands adiabatically (without gaining or losing heat), it's pressure P and volume V are related by the equation PV^1.4=C where C is a constant. Suppose that at a certain instant the volume is 510 cubic centimeters and the pressure is 87 kPa and is decreasing at a rate of 12 kPa/minute. At what rate in cubic centimeters per minute is the volume increasing at this time?
The figure shows data for a portion of the ducting in a ventilation system operating at steady state. The ducts are well insulated and the pressure is very nearly 1 atm throughout. The volumetric flow rate entering at state 2 is AV2 = 4400 ft3/min. Assume the ideal gas model for air with cp = 0.24 Btu/lb·oR and ignore kinetic and potential energy effects.
Derive the 7 general property equation of the following thermodynamics processes: a. ISOMETRIC PROCESS
The figure belows shows three components of an air-conditioning system, where T3= 115°F and m˙3= 1.5 lb/s. Refrigerant 134a flows through a throttling valve and a heat exchanger while air flows through a fan and the same heat exchanger. Data for steady-state operation are given on the figure. There is no significant heat transfer between any of the components and the surroundings. Kinetic and potential energy effects are negligible. Modeling air as an ideal gas with constant cp = 0.240 Btu/lb · °R, determine the mass flow rate of the air, in lb/s.
The pressure of the air in a starting vessel is 40 bar and the temperature is 24°C. If a fire in the vicinity causes the temperature to rise to 65 °C. Neglect anyincrease in the volume of the vessel which is 5 liters. determine the: a. work nonflow and heat transferred